Airaid 510-213 Installation Instructions

Installation Instructions

For Part Numbers:
510-213 720-476 Airaid Oiled Media Filter
511-213 721-476 SynthaMax Dry Media Filter - Red
512-213 722-476 SynthaMax Dry Media Filter - Black
513-213 723-476 SynthaMax Dry Media Filter - Blue

2007-2015 Toyota Tundra/Sequoia 5.7L V8
2007-2013 Toyota Tundra 4.6L V8
2008-2012 Toyota Sequoia 4.6L V8

Component Identification

1 Airaid Premium Filter 1
2 Intake Tube 1
3 MAF Panel 1
4 Bottom Panel 1
5 Filter Adapter 1
6 Urethane Hump Hose 1
7 Silicone Reducing Coupler 1
8 Weather Strip 37 ½” 1
Hardware and Instructions 1

9 6-32 x 5/16" Phillips Head Screw 4
10 #6 Flat Washer 4
11 Kep Nut 4
12 8-32 x ⅜" Button Head Screw 2
13 Button Head Cap Screw 6
14 1/4" Flat Washer 8
15 ¼-20 Flange Nut 3
16 10-32 Well Nut 1
17 10-32 Hex Bolt 1
18 #10 Fender Washer 1
19 12mm Hex Bolt 2
20 Hose Clamp #52 1
21 #56 Hose Clamp 1
22 #72 Hose Clamp 2
23 Barbed Fitting 1
24 ½" Barbed Connector 1
25 3/4 Speed Clamp 2
26 1/2" Breather Hose 1
27 Double Bend Bracket 1
28 L Bracket 1
29 #203 Bracket 1

C.

A.

B.

1. Disconnect the negative battery cable.
Remove the factory beauty cover.
A) Loosen the hose clamp on the factory intake

tube where it connects to the throttlebody.
B) Disconnect the Mass Air Flow sensor wiring
harness.
C) Unsnap the wiring harness anchor from the
factory airbox lid.

2. Disconnect the factory breather hose, and vac­uum hose from the factory airbox lid.

3. Unlatch the four metal clips that hold the air­box lid to the base and remove the intake tube and
lid from the vehicle. Remove the factory air filter
from the airbox base.

#140 Bracket

#203 Bracket

4. Using a 10mm socket, loosen the two bolts

that hold the airbox base to the fender well, and
remove it from the vehicle. There is one bolt on
the front of the base, and one bolt at the rear of
the base.

7. Install the CAD assembly into the vehicle.
Align the hole in the bottom over the captured
nut in the fender well. Install one 16mm hex bolt
(#16), and washer (#14). Leave loose for now.
Next reinstall the factory bolt removed in step #5,
thru the bracket, into the ground anchor in the
fender well.

5. Remove the rear ground anchor bolt from the
side of the fender well and save it for reuse in
step #7 .

8. Remove two screws, and remove the Mass Air
Flow sensor from the factory intake tube. Note

the orientation of the sensor in the tube. It will
need to be replaced in the same direction in the
Airaid tube.

#110 Bracket

6. Assemble the Cool Air Dam panels (#3 & #4)

as shown using four 6-32 screws (#9), washers
(#10), and keps nuts (#11). Install the filter adapt­er (#5) using three 1/4” button head bolts (#13)
and washers (#14). Install the 3 brackets (#24),
(#25), and (#26) as shown using three 1/4” bolts
(#13), washers (#14), and nuts (#15). Just snug
the bolts for now, they will be adjusted later.

9. Re-install the MAF sensor into the Airaid in-
take tube (#2) as shown using the supplied 8-

32x3/8” button head screws (#12).
Do Not Use The Factory Screws!

Next install the 1/8NPTx3/16” barbed fitting
(#20) into the Airaid tube.

Install bolt thru the
#110 bracket here.

10. Install the hump hose (#6) with two #72 hose

clamps (#19). Install the reducing coupler (#7)
with the small end on the throttlebody. Install the
#52 hose clamp (#17) over the throttlebody end,
and the #56 hose clamp (#18) over the large end
of the coupler. Leave the clamps loose for now.

13. Reconnect the MAF wiring harness to the
MAF sensor. Reconnect the factory breather hose

to the 1/2” barbed coupler using the factory
clamp. Reconnect the small vacuum hose to the
3/16” barbed fitting on the Airaid tube.

11. Install the Airaid intake tube into the hump
hose first, and then into the reducing coupler.
Center the tube between the throttlebody, and the
CAD, adjust for fit, and then tighten the four hose
clamps. Install one 6mmx12mm bolt (#16) and
washer (#14) thru the bracket into the captured
nut in the fender well.

14. Place Well Nut into 3/8” hole in core support.

12. Install the 1/2” breather hose (#23) onto the

nipple on the Airaid tube. Slide the 1/2” barbed
coupler (#21) into the installed breather hose, and
secure both ends with the supplied speed clamps
(#22).

15. Use supplied 10-32 hex head bolt and Fender
Washer to secure Panel Bracket. Do not over
tighten.

17. Double check your work!

Make sure there is no foreign material in the

18. Reconnect the negative bat­tery cable!

intake path. Make sure all clamps, hoses,
bolts, and screws are tight. Periodically check
the tightness of all hose clamps. Double check
the hood clearance.

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your

16. Install the Airaid Premium Filter (#1) onto the
filter adapter and tighten the clamp. Next install
the weather strip (#8) on top of the CAD as
shown. For an easier install, start at the fender
side of the CAD and work your way towards the
radiator. Reinstall the factory beauty cover.

part number, and click View Details.

FILTER IDENTIFICATION

720-476 Airaid Oiled Media 721-476 Airaid SynthaMax Dry Media - Red

722-476 Airaid SynthaMax Dry Media - Black 723-476 Airaid SynthaMax Dry Media - Blue

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris, care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is

For your Oiled media filter we

suggest using the AIRAID Fil-

ter Tune-Up Kit!

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze

to clean filter. Allow filter to air dry and
reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.02.10.15