Installation Instructions
For Part Numbers:
510-173 700-458 Airaid Oiled Media Filter
511-173 701-458 SynthaMax Dry Media Filter - Red
512-173 702-458 SynthaMax Dry Media Filter - Black
513-173 703-458 SynthaMax Dry Media Filter - Blue
2005-06 Toyota Tundra
2005-07 Toyota Sequoia
4.7L V8
Component Identification
1. Airaid Premium Filter 1
2. MAF Panel 1
3. Back Panel 1
4. MAF Adapter 1
5. MIT Intake Tube 1
6. 3 ½”to3 3/8”x2 Reducer 1
7. 3 ½”x3” Hump Hose 1
8. ½”x13” Hose 1
9. Weather Strip 22” 1
10. # 52 Hose Clamp 2
11. # 60 Hose Clamp 2
12. ¼”Barbx1/8”NPT 1
13. ¼”x1/4”x1/8” Vacuum Tee 1
14. ¼”IDx4” Hose 1
15. 6-32x5/16” Screw 3
16. #6 Flat Washer 3
17. 6-32 Keps Nut 3
18. ¼”x20 Button Head Bolt 3
19. ¼” Flat Washer 3
20. 8-32 Button Head Bolt 2
21. Hose Mount 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1. Stage I
Disconnect negative battery cable.
Remove 2 screws and remove and set aside the
Mass Air Flow sensor from the factory airbox.
Unclip wire harness from intake tube.
(See arrow)
2. Loosen hose clamp where intake tube connects
to the airbox.
3. Unlatch 4 clips on factory airbox
4. Remove factory airbox lid, and filter. 5. Remove fan shroud bolt on passenger side of
radiator, save for later use.
7. Slip MAF adapter into factory intake tube
while installing CAD onto top of factory airbox.
Adjust for fit, and latch 3 factory clips on factory airbox. Tighten the hose clamp on the intake
tube. Replace the fan shroud bolt that was removed in step #5.
8. Re-route MAF wire harness under the intake tube,
and around the front of the airbox. Install MAF sensor into the MAF adapter , using two supplied button
head screws (#20). DO NOT USE FACTORY
SCREWS!
6. Assemble Cool Air Dam (#2) & (#3) using
three screws (#15), washers (#16), and nuts
(#17). Install MAF adapter (#4) using two button
head bolts (#18), and washers (#19), as shown.
9. Slip hose mount (#21) over MAF wire harness,
and into hole in bottom of CAD. This will keep
the harness from chafing.
11. Stage II
For maximum airflow and aggressive sound
from your vehicle, proceed with installing the
Airaid Modular Intake Tube (#5). The MIT can
be added or taken off of the vehicle at any time
depending on your preference. If you choose
not to install the MIT, skip to step #19 below.
10. Install the Airaid Premium Filter (#1) on
the MAF adapter. Next install the weather
strip (#9) on the CAD as shown. Start at the
front, next to the radiator, and work your way
towards the back.
13. Remove two 10mm nuts, and the beauty
cover from the top of the engine. Remove one
bolt thru the Adel clamp that holds the air conditioning hose to the intake tube. Loosen hose
clamps on each end of the factory intake tube.
12. Disconnect breather hose from valve cover.
Disconnect 1/8” vacuum line, and 1/4” vacuum
line from the back of the factory intake tube.
14. Remove the factory intake tube. 15. Install the hump hose (#7) on the MAF
adapter (#4) with two hose clamps (#11).
Install the reducer (#6), small end first, onto
the throttle body with two hose clamps (#10).
Leave the clamps loose for now.
16. Install the barbed fitting (#11) into the
MIT as shown, and then slide the 1/4”x4’
hose (#13) over the fitting.
17. Install the MIT (#5) into the hump hose
(#7), and then into the reducer (#6). Adjust the
MIT snugly against the throttle body, and
tighten all 4 hose clamps. Install the supplied
button head bolt (#18), and washer (#19), thru
the Adel clamp and into the MIT to hold the
air conditioning hose.
18. Install the vacuum tee (#13) into the
1/4”x4” hose (#14), and reconnect the factory
1/4” and 1/8” vacuum lines to the tee as
shown. Install the 1/2”x13” breather hose (#8)
onto the valve cover and to the MIT as shown.
19. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts,
and screws are tight.
20. Reconnect the negative battery cable!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-458 Airaid Oiled Media 701-458 Airaid SynthaMax Dry Media - Red
702-458 Airaid SynthaMax Dry Media - Black 703-458 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a garden hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.
REV.01.06.14
Loading...