Airaid 510-134 Installation Instructions

Installation Instructions

For Part Numbers:

510-134 700-451 Airaid Oiled Media Filter
511-134 701-451 SynthaMax Dry Media Filter - Red
512-134 702-451 SynthaMax dry Media Filter - Black
513-134 703-451 SynthaMax Dry Media Filter - Blue

2001-04 Toyota Tacoma

3.4L V6

Component Identification

1. Airaid Premium Filter 1

2. MAF Air Dam Panel 1

3. Front Air Dam Panel 1

4. Black Plastic Tube Adapter 1

5. Black Plastic Intake Tube 1

6. Urethane Coupler 1

7. Urethane Hump Hose 1

8. Weather Strip 18 ½” 1

9. ¼-20 x 5/8” Hex Bolt 2

10. ¼” Flat Washer 2

11. 8-32 x ½” SS Button Screw 2

12. 6-32 x 5/16” Screw 4

13. #6 Flat Washer 4

14. 6-32 Keps Nut 4

15. 8mm x 1.25 Hex Bolt 3

16. 5/16” Flat Washer 3

17. ¼”NPT x 3/8” Barb Fitting 1

18. ¼” NPT x ¼” Barb Fitting 1

19. ½” x 5/8” Connector 1

20. #52 Hose Clamp 2

21. #48 Hose Clamp 2

22. ½” x 4” Breather Hose 1

23. ¼” x 16” Vacuum Hose 1

24. #16 Black Speed Clamp 2

25. 3/8” Nylon Spacer/Washer 2

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1.Disconnect The Negative Battery Terminal!
Loosen the two hose clamps on the factory intake tube.

2. Remove factory vacuum lines / hose from the facto­ry air box and intake tube. (Note: Retain the 3/8”

vacuum hose)

3. Disconnect the electrical connector from the Mass Air
Sensor.

4. With a 12mm socket, remove the three bolts securing
the factory air box assembly & remove the factory
air box assembly from vehicle.

7. Using two supplied ¼-20 bolts and washers, mount
the Airaid filter adapter to the Airaid Cool Air
Dam.

5. Loosen the two screws on the Mass Air Sensor and
remove the sensor from the factory air box. Retain
sensor for later use.

One
spacer
under
each
screw.

8. Using the two 8-32 Allen head screws and two plas-

tic spacers provided, mount the factory Mass Air
Sensor to the Airaid filter adapter tube. (Note: the

plastic spacers are placed between the Mass Air
Sensor and the Filter Adapter Tube with the
screws sliding through the spacers).

6. Assemble the Airaid Cool Air Dam using four small
screws, washers, and nuts provided.

9. Install two supplied ¼” NPT barbed fittings in Airaid
intake tube. (Note: Install 3/8” fitting in the for-
ward hole and the ¼” fitting in the back hole) Slide
hump hose and two #52 hose clamps on large end of
intake tube and slide coupler with two #48 hose
clamps on small end of tube. (Note: leave all hose

clamps loose for final assembly)

Secure air dam with
three bolts

10. Position the Airaid intake assembly in place of the

original, factory assembly. Using three supplied
8mm bolts and washers, mount the Airaid assem­bly using the three original/factory mounting
points.

13. Connect factory 3/8” vacuum line to nylon fitting
on intake tube & connect steel tube on intake mani­fold to ¼” fitting on intake tube with ¼” vacuum
line provided.

11. Connect the Airaid intake tube to the engine by slid­ing the coupler over the throttle body & adjust the
intake tube to insure proper alignment from the
throttle body to the air filter adapter. (Note: Leave

a gap between the tube and the air filter adapter to
allow for engine movement)

Front of vehicle

14. Using the supplied 5/8” to ½” barbed connector and

½” x 4” breather hose, connect the factory hose
located by the throttle body to the Airaid intake
tube. Use two supplied #16 Speed clamps to secure
the hose to the barbed ends.

12. Reinstall the electrical connector to the Mass Air
Sensor.

15. Mount the Airaid premium air filter inside the
Cool Air Dam & press weather strip onto the top
of the Cool Air Dam. (Hint: start at a corner and

work towards the ends)

16. Double check your work to be certain that all
nuts, bolts, and clamps are securely fastened.

17. Reconnect the negative battery cable.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-451 Airaid Oiled Media 701-451 Airaid SynthaMax Dry Media - Red

702-451 Airaid SynthaMax Dry Media - Black 703-451 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Synthamax Air Filters do not require
oil. Service air filter as needed by
cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of air
filter and allow to soak. Then flush
filter clean from the inside out with a
garden hose and repeat steps if nec­essary. Do not apply high pressure
water or air to clean filter. Allow fil­ter to air dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.10.25.13