Airaid 450-330 Installation Instructions

Installation Instructions

For Part Number:

450-330

2015 Ford Mustang 2.3l EcoBoost 4 Cyl.

Component Identification

1 Airaid Track Day Filter 1

2 Airaid Intake Tube 1
3 Top Panel 1
4 Bottom Panel 1
5 Filter Adapter 1
6 Weatherstrip 23" 1
7 Coupler 1
8 Hump Hose 1
9 #40 Hose Clamp 1
10 #56 Hose Clamp 1
11 #68 Hose Clamp 2
12 5/8 Aluminum Fitting 1
13 #8 Flat Washer 1
14 1/4" Button Head Screw 1
15 13/16" Grommet 1
16 O-Ring 1
17 ¼"-20 Button Head Screw 4
18 1/4" Flat Washer 3
19 1/4-20 Button Head Cap Screw 3
20 1/4” Lock Washer 4

Maximum performance potential requires custom tune.

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

Anchor

Air temp sensor

1. Remove the battery box cover in the cowl and discon-

nect the negative battery terminal.

2. Loosen the clamp on the intake tube and slide it off
of the airbox. Gently pry the harness anchor out of the
airbox and disconnect the air temp sensor.

3. Remove the 6mm airbox mounting bolt in the inner
fender and lift the entire airbox assembly out of the vehi­cle. Set the bolt aside for now. It is to be reused.

4. Be sure to retain speed clip in the inner fender .

Fitting

Grommet

7. Insert the Grommet and Aluminum Fitting into the

Airaid Intake tube as shown.

5. Loosen the clamp on the turbo inlet coupler.

#40

#56

9. Slide the Reducer and Clamps onto the turbo side of

the Intake Tube as shown. Leave the clamps loose for
now.

6. Disconnect the PCV and turbo bypass lines from the
intake tube and remove the tube from the vehicle.

8. Tilt the air temp sensor rearward so the locking tab
clears the ramp and rotate it counterclockwise 1/4 turn to
release it.

New

OLD

Lock Tab

10. Replace the OEM O ring on the sensor with the sup-

plied Airaid O ring.

8. Install the Filter Adapter onto the Panel Assembly as
shown, using the three 1/4-20 Button Head Screws and
Flat Washers.

11. Insert the air temperature sensor into the Airaid intake
tube as shown and secure it using the #8 Screw and
Washer.

9. Transfer the OEM air box grommet and anti-crush
sleeve into the Panel assembly as shown.

7. Remove the protective film from the Panels and cre­ate the assembly as shown using four 1/4 -20 Button
Head Screws and Lock washers.

10. Remove the drivers side fan shroud bolt and set it
aside.

11. Install the Panel assembly into the engine compart­ment as shown and secure using the OEM hardware
removed in steps 3 and 10.

17. Reconnect the PCV and bypass line to the Airaid
Intake Tube.

Cut

12. When properly installed, the Panel tab resides behind

the fan shroud as shown.

11. Slide the Hump Hose with two, #68 Clamps onto the
Filter Adapter .

13. Lower the Airaid Intake tube down into position
and slide the reducer onto the turbo inlet.

7. Slide the Airaid Intake Tube into the Hump Hose and
tighten all four Hose Clamps.

10. Split one edge of the remaining Grommet with a
sharp knife and run the AT harness through it. Install
the Grommet and harness into the Panel as shown and
reconnect the sensor.

11. Install the Airaid Premium Filter onto the Filter
Adapter. Install the weatherstrip on top of the Panel as­sembly as shown with the contour rolling away from the
filter.

7. Double check your work. Make sure all clamps, hos­es, bolts, and screws are tight. Double check the hood
clearance. Reconnect the negative battery cable.

For your Oiled media filter we suggest using

the AIRAID Filter Tune-Up Kit!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions

regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are

missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa-

ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter

is reusable and should be cleaned periodically.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV01.13.15