Airaid 400-799 Installation Instructions

Installation Instructions

For Part Numbers:

400-799 860-397 Airaid Oiled Media Filter
401-799 861-397 SynthaMax Dry Media Filter - Red
402-799 862-397 SynthaMax Dry Media Filter - Black
403-799 863-397 SynthaMax Dry Media Filter - Blue
400-999 Airaid M.I.T. Tube

2011-14 Ford F-150

5.0L V8

Component Identification

1. Airaid Premium Filter * 1

2. Airaid Intake Tube 1

3. Hump Hose 1

4. Silicone Coupler 1

5. 1/4NPT to 3/8"Hose Fitting 1

6. PCV FITTING 1

7. GROMMET 1

8. #56 Hose Clamp 1

9. #60 Hose Clamp 2

10. #64 Hose Clamp 1

* Filter included in Airaid Jr. kit only

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

A.

B.

1. Disconnect The Negative Battery Terminal!

2. A. Disconnect the two breather lines in the factory

intake tube .
B. Loosen the two intake clamps, and remove the facto­ry intake tube.

3. If installing the Airaid Jr. Kit, unfasten the three clips
on the left side of the factory airbox, and remove the up­per half of the factory airbox. Remove the factory air fil­ter element.

4. Install The Airaid Premium Filter (#1) into the air­box.

7. Install the hump hose (#3) and two #60 hose clamps
(#9) onto the Intake Tube as shown. Leave the hose
Clamps loose for now.

5. Reinstall the airbox upper half. 6. A.) Install the 3/8 “ Barbed Fitting (#5) into the thread­ed holt in the Intake Tube.
B.) Insert the 5/8” Grommet (#7) into the Intake tube as
shown. Complete the tube assembly by inserting the 5/8
PCV Fitting (#6) into the Grommet.

8. Install the Silicone Reducer (#4) and Hose clamps
onto the Airaid Intake Tube. Place the #56 Clamp (#18)
on the throttle body side of the Reducer, and the #64
Clamp (#9) on to the Tube side.

9. Install the Intake Tube onto the throttle body first, then
into the airbox. Tighten all of the Hose Clamps.

10. Reconnect the breather lines to the Airaid Intake
Tube.

11. Double check your work!

Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses,
bolts, and screws are tight. Double check the
hood clearance!

Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

860-397 Airaid Oiled Media 861-397 Airaid SynthaMax Dry Media - Red

862-397 Airaid SynthaMax Dry Media - Black 863-397 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.02.11.15