Airaid 400-272 Installation Instructions

Installation Instructions

For Part Numbers:

400-272 720-478 Airaid Oiled Media Filter
401-272 721-478 SynthaMax Dry Media Filter - Red
402-272 722-478 SynthaMax Dry Media Filter - Black
403-272 723-478 SynthaMax Dry Media Filter - Blue

2010-14 SVT Ford Raptor 6.2L
2011-14 Ford F-150 6.2L

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Front Panel 1

4. Rear Panel 1

5. Urethane Hump Hose 1
6a. Weather Strip Short 1
6b. Weather strip Tall 1

7. 6-32 x 5/16” Screw 4

8. 6-32 Keps Nut 4

9. #6 Flat Washer 4

10. 8-32 x 1/2” Button Head Screw 2

11. 8-32X 1/2”Button Head Bolt 2

12. 1/4” Flat Washer 2

13. #68 Hose Clamp 2

14. T-20 Torx Driver 1

1. Disconnect the negative battery cable!

Loosen the two intake clamps and remove the Factory
intake tube.

A

2. A.) Disconnect the Mass Air Flow (MAF) Sensor.

B.) Unfasten the three airbox clips on the left side, and

remove the upper half of the factory airbox.

3. Remove the factory air filter from the lower half of
the airbox.

Note: Tab is outside

4. Assemble the two Quick Fit panels (#3 & #4) as

shown using four 6-32 screws (#7) flat washers (#9)
and kep nuts (#8).

Tabs

5. Install the assembly onto the lower half of the facto-

ry airbox. Slide the metal tabs into the airbox slots, and
fasten the 3 airbox clips.

B

A

6. . Transfer the MAF sensor into the Airaid Intake

Tube (#2) and secure using two 8-32 x 1/2” button
head screws (#10). Do Not Use The Factory Torx

Head Screws

7. Install the Hump Hose (#5), and the clamps (#13)

onto the Intake Tube. Slide the hump hose and clamps
down the tube as far as they will go and leave the
clamps loose for now.

8. A.) Mount the Intake Tube to the Rear Panel using
the two 1/4-20 Button Head Bolts (#11) and 1/4” Flat
washers (#12).
B.) Slide the Hump Hose and clamps onto the engine
air inlet, check for alignment, and tighten the clamps.

9. Re connect the Mass Air Flow Sensor.

12. Double check your work!

Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses,
bolts, and screws are tight.
Periodically check the tightness of all hose
clamps.

13. Re-connect the negative battery

10. Install the Airaid Premium Filter (#1) to the mount-

ing flange inside the quick fit assembly.
For SVT Raptor vehicles:
Complete the installation by attaching the Short Weath­er Strip (#6a) to the top of the panels as shown.

11. For F-150 Harley Davidson, Lariat, and Platinum
models:
Complete the installation by attaching the Tall Weather
Strip (#6b) to the top of the panel as shown.

cable!

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part num-

ber, and click View Details.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-478 Airaid Oiled Media 721-478 Airaid SynthaMax Dry Media - Red

722-478 Airaid SynthaMax Dry Media - Black 723-478 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not require
oil. Service air filter as needed by
cleaning with common non-petroleum
all-purpose household cleaner and wa­ter. Simple Green®, Formula 409® or
equivalent works great. Apply cleaner
to outside of air filter and allow to soak.
Then flush filter clean from the inside
out with a garden hose and repeat steps
if necessary. Do not apply high pres­sure water or air to clean filter. Allow
filter to air dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.03.25.14