Airaid 400-114 Installation Instructions

Installation Instructions

For Part Numbers:

400-114 700-445 Airaid Oiled Media Filter
401-114 701-445 SynthaMax Dry Media Filter - Red
402-114 702-445 SynthaMax Dry Media Filter - Black
403-114 703-445 SynthaMax Dry Media Filter - Blue

1999- June 04 Ford F-250/F-350 Super Duty
Pickup 5.4L V8, 6.8L V10
2000- June 04 Ford Excursion 5.4L V8, 6.8L V10
*Does not fit vehicles produced after June 2004

Component Identification

1. Filter 1

2. Rear Back Panel 1

3. Left Side Panel 1

4. Filter Adapter 1

5. Hardware Pack 1

6. Weather Strip 1

7. Bushing 3

8. Gasket 4.5” 1

9. ¼”x20x7/8” Bolts 3

10. ¼”x20 Nuts 3

11. ¼” Washers 6

12. 32x5/16” Screw 6

13. 6/32 Nuts 6

14. #6 Washer 6

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number,
and click View Details.

I DISCONNECT NEGATIVE (-) BATTERY CABLE.

II Remove air filter.

a) Loosen clamp and separate. Remove filter.
b) Remove the FRONT half of air box, simply “pull up” to release. No tools needed. See Fig#2
c) These parts are not reinstalled in Airaid kit.
d) CAUTION: Do Not remove the REAR half of the air box or the “V”-BAND CLAMP.

III Remove air cleaner bracket.
a) Unbolt the 4 retaining bolts (10mm), and remove the bracket (See Fig#2) from the engine compartment.
b) Save the 4 bolts to reuse later. The bracket is not reused.

IV Assemble Airaid Cool Air Dam.
a) Bolt the two panels together with the supplied #6 hardware. See Fig#1
b) Bolt the Filter Adapter to the Back Panel with the supplied 1/4” hardware.

V Install in vehicle.
a) Set in place of the removed bracket.
b) Use the 4 saved 10mm bolts to fasten the Airaid assembly into the existing bracket mounting holes.

VI Connect to Airaid.

a) Slip supplied Rubber Gasket onto the 4.5” stub on the end of the Airaid assembly. This gasket will make
a seal between the Airaid and the stock rear half once connected. Be sure gasket is in place.

b) Slide stock rear half toward the Airaid and secure with the factory “V”-BAND CLAMP.
c) Press weather seal on to top edge of air box.

VII Finishing up
a) Check that no foreign objects are in the intake path.

b) Check throttle linkage for full open and closed travel.
c) Reconnect battery terminal. Enjoy!

Left Side Panel

Figure #1

Filter Adapter

Figure #2

Bracket

Rear Back Panel

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-445 Airaid Oiled Media 701-445 Airaid SynthaMax Dry Media - Red

702-445 Airaid SynthaMax Dry Media - Black 703-445 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a
garden hose and repeat steps if neces­sary. Do not apply high pressure water
or air to clean filter. Allow filter to air
dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.10.18.13