Airaid 350-199 Installation Instructions

Installation Instructions

For Part Numbers:

350-199 700-469 Airaid Oiled Media Filter
351-199 701-469 SynthaMax Dry Media Filter - Red
352-199 702-469 SynthaMax Dry Media Filter - Black
353-199 703-469 SynthaMax Dry Media Filter - Blue

2006-10 Dodge Charger 5.7L, 6.1L
2005-08 Dodge Magnum 5.7L, 6.1L
2005-10 Chrysler 300 5.7L, 6.1L
2008-10 Dodge Challenger 5.7L, 6.1L

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Back Panel 1

4. Airaid Intake Tube 1

5. Filter Adapter 1

6. Rear Support Bracket 1

7. Urethane Hump Hose 1

8. Reducing Coupler 1

9. Breather Hose 1

10. Weather Strip 20 1/2” 1

11. 3/8-16 x 1 1/4” Button Head Bolt 1

12. 3/8” Flat Washer 1

13. ¼ - 20 x 1/2” Button Head Bolt 6

14. ¼” Flat Washer 6

15. 1/4” Serrated Nut 3

16. 6-32 x 5/16” Screw 5

17. #6 Flat Washer 5

18. 6-32 Keps Nut 5

19. #52 Hose Clamp 2

20. #72 Hose Clamp 2

21. Grommet 1

22. Well Nut 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.

If you are working on a 5.7L, first remove
the engine beauty cover by lifting it up off of
the grommets. Next, loosen the hose clamp

that holds the factory intake tube to the
throttle body.

2. Disconnect the breather hose from the
factory airbox lid.

3. Pull both lockdown tabs towards you on
the factory airbox lid to remove the lid from
the base.

4. Lift the intake tube towards you, and
without disconnecting the wiring harness,
gently remove the temperature sensor from
the factory intake tube, and set it aside.

7. Assemble the two Cool Air Dam (CAD)
panels (#2, #3) using five 6-32 x 5/16”
screws (#16), #6 flat washers (#17), and 6­32 keps nuts (#18).

5. Remove the factory intake hose and lid
assembly from the vehicle. Remove the
factory air filter.

8. Next, install the filter adapter (#5) using
three ¼ - 20 x 1/2” button head bolts (#13),
and ¼ flat washers (#14).

6. With a 10mm socket, remove and save
the bolt that holds the factory air filter base
to the radiator support. Remove the air filter
base from the vehicle.

9. Slip the well nut (#22) into the hole in
the inner fender.

10. Install the CAD into the vehicle. Re­install the factory bolt removed in step #6
thru the CAD and into the radiator support.
Next install the 3/8-16 x 1 1/4” button head
bolt (#11) and 3/8” flat washer (#12) thru
the CAD and into the well nut. Tighten
both bolts.

A.

B.

11. Remove the 10mm nut from the stud

on the driver’s side inner fender and save it
for the next step.

12. Install the rear support bracket (#6)
from the CAD to the inner fender using
three ¼ - 20 x 1/2” button head bolts (#13),
¼” flat washers (#14), 1/4” serrated nuts
(#15), and the 10mm factory nut removed
in step #11.

13. A. Insta ll the urethane hump hose
(#7) onto the filter adapter using two #72
hose clamps (#20), (Leave loose for now).
B. Install the la r ge end of the r educing
coupler (#8) on the Airaid Intake Tube
(#4), using two #52 hose clamps (#19).
Tighten only the hose clamp on the tube.

16. If you are working on a 5.7L, skip to
step #17. If you ar e working on a 6.1L, re-

connect the factory breather tube to the
Airaid Intake Tube as shown.

14. Install the Airaid Intake Tube into the
hump hose first, and then onto the throttle
body, making sure it is flush against the
throttle body, adjust for fit, now tighten all
of the hose clamps.

17. If you are working on a 6.1L, skip to
step #18. If you are working on a 5.7L,

install the breather hose (#9) from the
valve cover to the Airaid Intake Tube as
shown. Re-install the beauty cover onto the
engine.

15. Install the grommet (#21) into the hole
in the Airaid Intake Tube, and then gently
push the temperature sensor (removed in
step #4) thru the grommet until completely
seated.

18. Install the Airaid Premium Filter (#1),
onto the filter adapter inside of the CAD,
and tighten the hose clamp. Next install the
weather strip (#10) onto the top of the

CAD.

19. Double check your work!

20. Reconnect the negative battery cable!

Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red

702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.7.13