Airaid 350-193 Installation Instructions

Page 1
Installation Instructions
For Part Numbers:
350-193 700-469 Airaid Oiled Media Filter 351-193 701-469 SynthaMax Dry Media Filter - Red 352-193 702-469 SynthaMax Dry Media Filter - Black 353-193 703-469 SynthaMax Dry Media Filter - Blue
2006-10 Dodge Charger SRT-8/Super Bee 2008 Dodge Magnum SRT-8
6.1L With Hood Scoop
Component Identification
1. Airaid Premium Filter 1
2. MAF Panel 1
3. Back Panel 1
4. Airaid Intake Tube 1
5. Hood Scoop Tube 1
6. Filter Adapter 1
7. Urethane Hump Hose 1
8. Reducing Coupler 1
9. Weather Strip 20 1/2” 1
10. 3/8-16 x 1 1/4” Button Head 1
11. 3/8” Flat Washer 1
12. ¼ - 20 Button Head Bolt 4
13. ¼” Flat Washer 4
14. 8-32 x 3/8” Button Head Screw 3
15. #8 Flat Washer 3
16. 6-32 x 5/16” Screw 5
17. #6 Flat Washer 5
18. 6-32 Keps Nut 5
19. #52 Hose Clamp 2
20. #72 Hose Clamp 2
21. Grommet 1
22. Well Nut 1
23. L-Bracket 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1. Disconnect the negative battery cable.
Loosen the hose clamp that holds the fac­tory intake tube to the throttle body.
2. Disconnect the breather hose from the factory airbox lid.
3. Pull both lockdown tabs towards you on the factory airbox lid to remove the lid from the base.
4. Lift the intake tube towards you, and without disconnecting the wiring harness, gently remove the temperature sensor from the factory intake tube, and set it aside.
7. Assemble the Airaid Cool Air Dam (CAD) pa nels (#2, #3) using five 6-32 x 5/16” screws (#16), #6 flat washers (#17), and 6-32 keps nuts (#18).
5. Remove the factory intake hose and lid assembly from the vehicle. Remove the factory air filter.
8. Next install the filter adapter (#6) using three ¼ - 20 button head bolts (#12), and ¼” flat washers (#13).
6. With a 10mm socket, remove and save the bolt that holds the factory air filter base to the radiator support. Remove the air filter base from the vehicle.
Page 2
10. Install the assembled Cool Air Dam into the vehicle. Re-install the factory bolt removed in step #6 thru the CAD and into the radiator support. Next install the 3/8-16 x1 1/4” button head bolt (#10) and 3/8” flat washer (#11) thru the CAD and into the well nut. Tighten both bolts.
A.
B.
11. Remove the factory 10mm nut from the
stud on the driver’s side inner fender and save it for the next step.
12. Install the hood scoop into the CAD using three 8-32 x 3/8” button head screws (#14), and three #8 flat washers (#15), leave loose. Install the L-bracket (#23) over the stud on the fender, and bolt it to the hood scoop using one 1/4-20 button head bolt (#12), and 1/4” flat washer (#13). Replace the factory nut on the stud, adjust for fit, and tighten all bolts, nuts, and
13. A. Install the ur ethane hump hose (#7) on the filter adapter using two #72 hose clamps (#20), (Leave loose for now). B. Install the r ed ucing coupler (#8) large end on the Airaid Intake Tube (#4), using two #52 hose clamps (#19). Tighten only the hose clamp on the tube.
16. Re-connect the factory breather tube to the Airaid Intake Tube as shown.
14. Install the Airaid Intake Tube into the hump hose first, and then onto the throttle body, making sure it is flush against the throttle body, adjust for fit, now tighten all of the hose clamps.
17. Install the Airaid Premium Filter (#1), onto the filter adapter inside of the CAD, and tighten the hose clamp. Next install the weather strip (#9) onto the top of the CAD.
15. Install the grommet (#21) into the hole in the Airaid Intake Tube, and then gently push the temperature sensor (removed in step #4) thru the grommet until completely seated.
18. Double check your work!
Make sure there is no foreign materi­al in the intake path. Make sure all clamps, hoses, bolts, nuts, and screws are tight. Double check the hood clearance.
19. Reconnect the negative battery cable!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red
702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
Synthamax Air Filters do not require oil. Service air filter as needed by cleaning with common non-petroleum all-purpose household cleaner and water. Simple Green®, Formula 409® or equivalent works great. Apply cleaner to outside of air filter and allow to soak. Then flush filter clean from the inside out with a gar­den hose and repeat steps if necessary. Do not apply high pressure water or air to clean filter. Allow filter to air dry and reinstall.
P/N 790-551 Aerosol Spray P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.11.7.13
Loading...