Airaid 350-171 Installation Instructions

Installation Instructions

For Part Numbers:

350-171 700-452 Airaid Oiled Media Filter
351-171 701-452 SynthaMax Dry Media Filter - Red
352-171 702-452 SynthaMax Dry Media Filter - Black
353-171 703-452 SynthaMax Dry Media Filter - Blue

2005-10 Chrysler 300C 2.7L V6, 3.5L V6
2009-10 Dodge Challenger 3.5L V6
2006-10Dodge Charger 2.7L V6, 3.5L V6
2005-08 Dodge Magnum 2.7L V6, 3.5L V6

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Front Panel 1

4. 1/2” x 14” Breather Hose 1

5. Weather Strip 27’” 1

6. 6-32x5/16” Screw 4

7. #6 Flat Washer 4

8. 6-32 Keps Nut 4

9. ½” Rubber Elbow 1

10. #18 Speed Clamp 3

11. #16 Speed Clamp 3

12. ½”x ½” Connector 2

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.

Remove the breather hose from the
factory air box lid and valve cover.

2.7L Engines: remove the hard plastic
breather tube at the elbow near the

2. Loosen the hose clamp on the facto-

ry intake tube, located at the air box
lid.

3. Remove the airbox lid by pulling the

tabs towards the front of the car. Then,
lift the lid up and slide it forward, and
remove it from the bottom of the air­box.

back of the valve cover.

4. Remove the factory air filter from

the bottom of the airbox.

7. Slide the three tabs on the back of

the Quick Fit panels into the factory
airbox. (For 2005-2006 models, make

sure the 1/2” rubber elbow (#8) slides
onto the valve cover breather nipple.)

Push the front of the Quick Fit panels
down, until the locking tabs snap into
place. 2.7L Engines: Skip to step #9.

5. Assemble the Quick Fit panels (#2,

#3) using four 6-32x 5/16” screws
(#5), #6 flat washers (#6), and 6-32
keps nuts (#7).

2007 3.5L Engines
Only

8. For 2007 3.5L Engines, (shown

above), slide one end of the 1/2”x 1/2”
connector (#10) into the rubber elbow.
Slide the other end into the factory
breather hose. Install one speed clamp
(#9) over the factory breather hose and
1/2” connector as shown.

6. Slide the 1/2” rubber elbow (#8) on-

to the breather fitting on the side of the
Quick Fit panels. Install 2
#18speed clamps (#9), one over each
end of the elbow, (Do not tighten the

clamps at this time.)

#16 speed clamps

#18 speed clamp

1/2” connectors

2.7L Engines

9. 2.7L Engines: Install the two 1/2”

connectors (#12),into each end of the
supplied breather hose (#4). Connect the
breather hose to the rubber elbow on the
Quick Fit Panel using one #18 speed
clamp (#10), and one #16 speed clamp
(#11). Install one #16 speed clamp on the
opposite end of the hose as shown.

10. For 2.7L Engines: After installing

the Quick Fit Panels, (Refer to step #7),
connect the breather hose to the factory
elbow at the back of the valve cover
using one #16 speed clamp.
(Factory intake tube removed for in­struction purposes).

11. Slide the Airaid Premium Filter (#1)

onto the Quick Fit panel tube, and
tighten the hose clamp. Install the fac­tory intake tube onto the opposite end
of the Quick Fit panel tube, and tighten
the hose clamp. Tighten the speed
clamps on the breather hose, and the
1/2” rubber elbow.

12. Install the weather strip (#4) on the top

of the Quick Fit panels. (Hint: Start at one
end and work all the way to the other end).

13. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.

14. Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-452 Airaid Oiled Media 701-452 Airaid SynthaMax Dry Media - Red

702-452 Airaid SynthaMax Dry Media - Black 703-452 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.12.3.13