Airaid 311-770 Installation Instructions

#311-770 Jr. Kit Instructions

2005-2010 Jeep Grand Cherokee 5.7L Hemi

Thank you for purchasing the Airaid Modular Intake System or Jr. Kit. Please read the instruction
manual carefully before proceeding with the installation. Contact Airaid @ [phone] 8:00 AM - 5:00 PM
MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid components
were carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If
any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and
debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS
RESPONSIBILTY!

Thank you for selecting Airaid.

Packing List:

KIT170T Modular Intake Tube 1

851-233 Airaid Premium Filter 1

KITCOUPLER03 Coupler 3 ½”x 3” 1

KITHUMPHS03 Hump Hose 3 ½”x3” 1

KIT770HP Hardware & Instructions 1

-KITGRMT03 Grommet 1

-KIT110T Nylon zip tie 1

-KITHS60 #60 Hose Clamp 4

Tools Required for this Installation:

10mm Socket

5/16” Socket , Extension, Ratchet,

Side Cutter Pliers

Installation Instructions. Read Me!

1. Disconnect the negative

battery cable. Loosen hose

clamp on air cleaner box lid.
Carefully twist and remove the
breather hose from the lid.

2. Remove oil fill cap and set

aside.

3. Carefully lift the engine cover

for access to the throttle body.

(There are only grommets that
hold down the cover, no
bolts.)

A.

B.

4. A.) Using the 10mm socket,

remove the bolt that holds the
stock intake system. B.)
Loosen the hose clamp that
holds the coupler to the
throttle body.

5. Carefully pull the intake

towards you and rotate it so
the bottom faces you, and cut
the tie wrap that holds the
breather tube, as shown.

6. Slide the clip off of the intake

tube that holds the breather
line.

7. Carefully twist and rem ove the

temperature sensor from the
stock intake tube. Remove the
stock intake tube from the
vehicle.

8. If you purchased an Airaid Jr.

Kit, unhook the two clips and
remove the factory air filter,
and replace it with the Airaid
Premium Filter supplied in the
kit.

9. Reconnect the breather hose.

Install the hump hose and two
#60 hose clamps as shown. Do

not tighten the clamps.

10. Install the coupler and two

#60 hose clamps on the
throttle body as shown. Do
not tighten hose clamps.
Fasten the factory breather
hose to air conditioning line
using the supplied zip tie.

11. Install the supplied grommet

into Airaid MIT as shown.

12. Carefully install the

temperature sensor into the
Airaid MIT as shown. Make
sure it’s pushed all the way in
and the plug is connected to
the wire harness.

Second

13. Install the MIT into the hump

hose first, and then into the
throttle body coupler. Adjust
to fit, and tighten the hose
clamps.

14. Re-install the engine cover by

firmly pushing it back into the
grommets.

15. Re-install the oil fill cap.

16. Check for any foreign material

in the intake path. Re-check
your work for tightness. Re-

connect the negative battery
cable.

m

Before

After!

Synthamax Air Filters do not require oil. Service air filter as needed by
cleaning with common non-petroleum all-purpose household cleaner and
water. Simple Green®, Formula 409® or equivalent works great. Apply
cleaner to outside of air filter and allow to soak. Then flush filter clean from
the inside out with a garden hose and repeat steps if necessary. Do not apply
high pressure water or air to clean filter. Allow filter to air dry and reinstall.

Instructions Revision
Date: 10/26/10

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.co