Airaid 310-770 Installation Instructions

Installation Instructions

For Part Numbers:

310-970 Modular Intake Tube
310-770 Jr. Kit 850-233 Airaid Oiled Media Filter
311-770 Jr. Kit 851-233 SynthaMax Dry Media Filter - Red

2005-10 Jeep Grand Cherokee
2006-10 Jeep Commander

5.7L V8 Hemi

Component Identification

1. *Airaid Premium Filter 1

2. Modular Intake Tube 1

3. Coupler 3 ½”x 3” 1

4. Hump Hose 3 ½”x3” 1

5. Grommet 1

6. Nylon zip tie 1

7. #60 Hose Clamp 4

* Filter included only in Jr. Kits

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.

Loosen hose clamp on air cleaner box lid.
Carefully twist and remove the breather
hose from the lid.

2. Remove oil fill cap and set aside. 3. Carefully lift the engine cover for access to
the throttle body. (There are only grom-

mets that hold down the cover, no bolts.)

4. A.) Using the 10mm socket, remove the
bolt that holds the stock intake system.
B.) Loosen the hose clamp that holds the
coupler to the throttle body.

7. Carefully twist and remove the temperature
sensor from the stock intake tube. Remove
the stock intake tube from the vehicle.

5. Carefully pull the intake towards you and
rotate it so the bottom faces you, and cut
the tie wrap that holds the breather tube,
as shown.

8. If you purchased an Airaid Jr. Kit, unhook
the two clips and remove the factory air
filter, and replace it with the Airaid Premi­um Filter supplied in the kit.

6. Slide the clip off of the intake tube that holds
the breather line.

9. Reconnect the breather hose. Install the
hump hose and two #60 hose clamps as
shown. Do not tighten the clamps.

10. Install the coupler and two #60 hose
clamps on the throttle body as shown. Do
not tighten hose clamps. Fasten the facto­ry breather hose to air conditioning line
using the supplied zip tie.

11. Install the supplied grommet into Airaid
MIT as shown.

12. Carefully install the temperature sensor into
the Airaid MIT as shown. Make sure it’s
pushed all the way in and the plug is connected
to the wire harness.

13. Install the MIT into the hump hose first,
and then into the throttle body coupler. Adjust
to fit, and tighten the hose clamps.

16. Check for any foreign material in the in­take path. Re-check your work for tight­ness. Re-connect the negative battery

cable.

14. Re-install the engine cover by firmly push-

ing it back into the grommets.

15. Re-install the oil fill cap.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

850-233 Airaid Oiled Media 851-233 Airaid SynthaMax Dry Media - Red

852-233 Airaid SynthaMax Dry Media - Black 853-233 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the

AIRAID Filter Tune-Up Kit!

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

to clean filter. Allow filter to air dry and
reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.12.2.13