Airaid 310-212 Installation Instructions

Installation Instructions
For Part Numbers:
310-212 700-539 Airaid Oiled Media Filter 311-212 701-539 SynthaMax Dry Media Filter - Red 312-212 702-539 SynthaMax Dry Media Filter - Black 313-212 703-539 SynthaMax Dry Media Filter - Blue
3.6L V6, 5.7L V8
Component Identification
1. Airaid Premium Filter 1
2. Rear Panel 1
3. Front Panel 1
4. Weather Strip 22” 1
5. 1/2”x13” Breather Hose 1
6. Mounting Bracket 1
7. 1/2”x90deg. Elbow 1
8. ¼-20 Button Head Bolt 2
9. ¼” Flat Washer 2
10. 1/4-20 Flange nut 2
11. 8-32 Thread Cutting Screw 10
12. Rubber Bumper 1
NOTE: These instr uct ions depict an insta llation being performed on a Jeep Grand Cherokee 5.7l and is meant to be a guide for all other makes and models listed. While some details may vary from vehicle to vehicle, the general install procedure remains the same.
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
B.
A.
Disconnect The Negative Battery Terminal!
1. Remove the engine cover.
2. A) Loosen the hose cla mp on the air box side of the
factory intake tube. B) Disconnect the crankcase breather line from the airbox lid.
3. Using a standard head screwdriver, carefully pry and separate the hose anchor from the airbox lid. This anchor will be reused on the Airaid Intake System.
4. Remove the upper half of the airbox and the factory air filter.
7. Fit the Front and Rear Panels (#2 and #3) together as shown with the tabs on the inside.
5. Carefully separate the hood seal from the cleat on the airbox inlet. Pull gently from side to side to avoid tear­ing the seal.
8. Join the Panels together using the ten, 8-32 Thread Cutting Screws (#11).
6. Unseat the lower half of the factory airbox from it’s mounting grommets and remove the airbox and air inlet duct as an assembly.
A
9. A.) Inst all the Rubber bu mper (#12) int o the sma ll
hole in the panel assembly. B.) Tr ansfer one of the factor y a ir box grommets int o the large hole in the Panel as shown.
B
10. Transfer the factory air inlet from the airbox and into
the Panel assembly.
11. Install the Mounting Bracket (#6) onto the Panel as­sembly using the two 1/4-20 Button Head Bolts (#8), 1/4” Flat Washers (#9), and 1/4-20 Flange nuts (#10).
12. Remove the bolt securing the power steering reser­voir and set it aside. This bolt will be reused in step 13. to hold the Mounting bracket.
13. Install the Panel assembly into the engine compart­ment as shown. Slide the Mounting bracket underneath the power steering reservoir and the airbox mounting post through the grommet in the Panel. Secure the as­sembly by reusing the bolt from step 12. Connect the factory intake tube to the Airaid Intake tube and tighten the clamp.
16. Install the Weather Strip (#4) to the top edge of the panels, and reattach the hood seal.
14. On V8 motors, replace the factory crankcase breather line with the 13” Breather Hose (#5) and connect it to the Airaid Intake Tube. Disregard the 90 deg. Elbow (#7) it will not be used.
17. Install the Airaid Premium Filter.
15. On V6 motors, connect the factory crankcase
breather hard line to the Airaid Intake Tube using the 90 deg. Breather Elbow (#7). Disregard the 13” Breath­er Hose (#6) it will not be used.
16. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight. Double check the hood clearance!
Reconnect the negative battery cable!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-539 Airaid Oiled Media 701-539 Airaid SynthaMax Dry Media - Red
702-539 Airaid SynthaMax Dry Media - Black 703-539 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter
we offer the Airaid Tune Up
Kit!
Synthamax Air Filters do not require oil. Service air filter as needed by cleaning with common non-petroleum all-purpose house­hold cleaner and water. Simple Green®, Formula 409® or equivalent works great. Apply cleaner to outside of air filter and al­low to soak. Then flush filter clean from the inside out with a garden hose and repeat steps if necessary. Do not apply high pres­sure water or air to clean filter. Allow filter
P/N 790-551 Aerosol Spray P/N 790-550 Squeeze Spray
to air dry and reinstall.
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.11.11.13
Loading...