Airaid 310-208 Installation Instructions

Installation Instructions

For Part Numbers:

310-208 700-471 Airaid Oiled Media Filter
311-208 701-471 SynthaMax Dry Media Filter - Red
312-208 702-471 SynthaMax Dry Media Filter - Black
313-208 703-471 SynthaMax Dry Media Filter - Blue

2007-11 Jeep Wrangler (JK)

3.8L V6

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. MAF Panel 1

4. Bottom Panel 1

5. Reducing Hump Hose 1

6. Weather Strip 20” 1

7. 1/4-20x1/2” Button Head Bolt 3

8. 1/4” Flat Washer 3

9. 1/4” Serrated Nut 1

10. 6-32x 5/16” Screw 7

11. #6 Flat Washer 7

12. 6-32 Keps Nut 7

13. 3/8-16x1 1/4”Button Head Bolt 2

14. Bracket 1

15. #44 Hump Hose 1

16. #52 Hose Clamp 1

17. Grommet 1

18. Well Nut 2

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.
Very Carefully r emove th e temp erat ur e sen­sor from the factory intake tube by using a circu­lar motion while pulling it straight out. There is
no need to disconnect the wiring harness.

2. Loosen the intake tube hose clamp on the
throttle body.

3. Unlatch the 4 metal clips that hold the
factory air cleaner lid to the base. Next dis­connect the breather hose that attaches to the
rear of the air cleaner lid.

4. Remove the factory intake tube, and lid from
the vehicle as an assembly.

7. With a 10mm socket, remove and save the
bolt from the factory plastic air cleaner mount. It
will be re-installed in step #12.

5. While rocking the factory air cleaner base
back and forth, pull up, and remove it from the
vehicle. There are no bolts holding it down, just
grommets.

8. With a 10mm socket, remove and save the bolt
that holds the radiator to the radiator support. It
will be reused in step #10.

6. Remove the 2 lower grommets from the
factory plastic air cleaner mount.

9. Install the 2 well nuts (#18) into the holes
in the plastic air cleaner mount where you
removed the grommets in step #6.

10. Insert the bolt, removed in step #8, thru
the round hole in the provided L-bracket, and
back into the radiator support. Leave the bolt
slightly loose for now.

11. Assemble the Cool Air Dam panels (#3 & 4)

as shown, using the seven 6-32 screws (#10), flat
washers (#11), and keps nuts (#12).

12. Install the CAD into the vehicle. Install
the two 3/8 x1 1/4” button head bolts (#13),
thru the bottom panel, and into the well nuts.
Reinstall the factory bolt removed in step #7
thru the panel, and into the fender well.
Tighten all three bolts at this time.

#44

#52

13. Using one 1/4” button head bolt (#7), 1/4”

flat washer (#8), and 1/4” serrated nut (#9),
attach the CAD panel to the L-bracket, as
shown. Now tighten the radiator mounting
bolt on the other end of the L-bracket.

16. Install the Airaid Intake Tube into the
hump hose first, and then rotate it down, and
into the CAD. Install two 1/4” button head
bolts (#7), and 1/4” flat washers (#8) thru the
CAD, and into the inser ts in the tube. Adjust
for fit, and tighten both hose clamps, and bolts.

14. Install the supplied grommet (#17) into the
Airaid Intake Tube (#2).

17. Very Carefully r einstall the t emper atur e
sensor removed in step #1, into the grommet in the
Airaid Intake Tube. Reconnect the factory breather
hose to the nipple on the intake tube.

15. Install the reducing hump hose (#5) onto
the throttle body as shown, with the #44 hose
clamp (#15) on the back, and the #52 hose
clamp (#16) on the front. Leave the clamps
loose for now.

18. Install the Airaid Premium Filter (#1) onto
the intake tube, and tighten the clamp. Next
install the weatherstrip (#6) onto the top of the

CAD as shown.

19. Double check your work!

20. Reconnect the negative battery cable!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses,
bolts, and screws are tight. Periodically check all clamps, and fasteners for tightness.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-471 Airaid Oiled Media 701-471 Airaid SynthaMax Dry Media - Red

702-471 Airaid SynthaMax Dry Media - Black 703-471 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.7.13