Airaid 310-205 Installation Instructions

Installation Instructions

For Part Numbers:

310-205 700-452 Airaid Oiled Media Filter
311-205 701-452 SynthaMax Dry Media Filter - Red
312-205 702-452 SynthaMax Dry Media Filter - Black
313-205 703-452 SynthaMax Dry Media Filter - Blue

2005-07 Jeep Grand Cherokee

3.7L V6

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Front Panel 1

4. Air Filter Adapter 1

5. Modular Intake Tube 1

6. Reducer 1

7. Hump Hose 1

8. Weather Strip17” 1

9. 90º Nylon Fitting 1

10. ¼-20x1/2” Button Head Screw 2

11. ¼” Flat Washer 2

12. Rubber Grommet 1

13. #48 Hose Clamp 1

14. #52 Hose Clamp 1

15. #56 Hose Clamp 2

16. 6-32x5/16” Phillips Screw 5

17. #6 Flat Washer 5

18. 6-32 Keps Nut 5

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.
Loosen the hose clamp that holds the factory intake
tube to the resonator.

2. Unlatch the two clips on the factory air cleaner box
lid.

3. Disconnect the factory breather tube from the air
cleaner box lid.

4. Remove the air cleaner lid, and factory intake tube
from the resonator box.

7. Using the 5/16” socket, ratchet and extension (or
flat blade screw driver)- loosen hose clamp on the
throttle body. This clamp is located close to the fire­wall, in the center of the engine compartment.

5. Remove the factory air filter.

8. Remove the factory intake resonator box from the

throttle body by pulling the box towards the radiator
and then lifting up.

6. Disconnect the intake air temperature sensor wir­ing harness, by squeezing the tab on the side, and
sliding the connector off.

9. Assemble the Quick Fit panels as shown, using
five 6-32 screws (#16), #6 washers (#17), and keps
nuts (#18).

10. Install the 90° nylon fitting (#9), into the air
filter adapter.

11. Install the Quick Fit panels into the factory
lower airbox by lining up the three tabs in the rear
of the panel, the latch holes in the front, and then re

-latching the factory airbox clips. Next, using the
1/4– 20x1/2” button head screws (#10) and 1/4”
flat washers (#11), install the air filter adapter into
the Quick Fit Panel.

12. Install the provided reducer (#3) onto the throt­tle body with the smaller diameter towards the
throttle body. Place the #48 hose clamp (#6) on
the smaller diameter section of the reducer (throttle
body side). Place the #52 hose clamp (#7) on the
larger diameter side of the reducer. Leave the
clamps loose for now.

13. Install the provided hump hose (#7) onto the
air filter adapter. Place a #60 hose clamp (#15) on
each side of the hump hose. Tighten only the
clamp on the air filter adapter. Leave the other
clamp loose for now.

A

B

16. A.) Install the Modular Intake tube into the

hump hose end first. B.) Insert the opposite end of
the Modular Intake tube into the reducer, on the
throttle body. Adjust components for fit, and then
tighten all of the hose clamps, and reconnect the
factory intake air temp sensor wiring harness.

14. Remove the factory intake air temp sensor from
the resonator box by carefully twisting the sensor
body, and pulling it straight out of its mount. Place
the sensor in a safe location, it will be re-used in
step #15.

17. Install the Airaid Premium Filter (#1) onto the
air filter adapter. Next, install the weather strip
(#8) on the top of the Quick Fit panels as shown.

19. Double check your work!

Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.

15. Install the rubber grommet (#12) into the Mod­ular Intake Tube (#5). Next, slide the factory in­take air temp sensor into the grommet in the tube.
Make sure it is seated all of the way in.

18. Reconnect the factory breather hose onto the
90º nylon fitting (#9).

20. Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-452 Airaid Oiled Media 701-452 Airaid SynthaMax Dry Media - Red

702-452 Airaid SynthaMax Dry Media - Black 703-452 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

to clean filter. Allow filter to air dry and
reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.7.13