Airaid 310-200 Installation Instructions

Installation Instructions

For Part Numbers:

310-200 700-458 Airaid Oiled Media Filter
311-200 701-458 SynthaMax Dry Media Filter - Red
312-200 702-458 SynthaMax Dry Media Filter - Black
313-300 703-458 SynthaMax Dry Media Filter - Blue

2006-10 Jeep Commander

5.7L V8

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Front Panel 1

4. Airaid Intake Tube 1

5. 3 1/2”x4 1/2”Hump Hose 1

6. 3 1/2” to 3 3/8” Reducer 1

7. Weather Strip 17 1/2” 1

8. Grommet 1

9. #56 Hose Clamp 2

10. #56 Hose Clamp 2

11. Speed Clamp 1

12. 6-32x5/16” Screw 4

13. #6 Flat Washer 4

14. 6-32 Keps Nut 4

15. Nylon Zip Tie 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.
Loosen the hose clamp on air cleaner box lid.

Twist and remove the breather hose from the
air cleaner box lid.

2. Unhook the two air cleaner lid latches on the
front of the airbox.

3. Remove the air cleaner box lid by sliding it
forward, and then up, and out of the factory
intake tube.

4. Remove factory air filter from the air clean­er box.

B.

A.

7. A.) Loosen the hose clamp on the throttle

body. B.) With a 10mm socket, remove the
bolt next to the throttle body that holds the
intake resonator in place.

5. Remove, and set aside the oil filler cap.

Use caution not to drop anything into the

engine while the cap is off.

8. Carefully pull the resonator towards you and
rotate the bottom up to gain access to the tie
wrap holding the breather hose to the rubber
coupler. Cut the tie wrap and discard.

6. Carefully lift up on the engine cover (it is
held in place by grommets, no bolts) to

access the hose clamp on the throttle
body, and 10mm bolt next to the throttle
body.

9. Slide the clip off of the resonator that holds
the breather tube in place.

10. Carefully twist and remove the tempera­ture sensor from the bottom of the reso­nator, and then remove the resonator
from the vehicle.

11. Assemble the two pieces of the Quick Fit
panels as shown (#2), using the four 6­32 screws (#12), washers (#13), and nuts
(#14), that are provided in the kit.

12. Install the weather strip (#7) on the
top of the Quick Fit assembly. (Hint:

start at one end, and go towards the
other end, don’t start in the middle.)

13. Install the Quick Fit assembly in the bot­tom of the stock air box by sliding the
four tabs on the back into the slots on the
airbox, once installed, re-hook the two
latches. Next, install the speed clamp
(#10) over the breather hose and connect
it to the Quick Fit assembly as shown.

16. Install the supplied grommet (#8) into the
hole in the back of the tube.

14. Install the hump hose (#5) and two #60 hose
clamps (#10) on the Quick Fit assembly.

Do not tighten the clamps at th is time.

17. Carefully install the factory temperature sen-

sor into the grommet. Make sure it is seated
all the way in.

15. Install the reducer (#6) and two #56
hose clamps (#9) on the throttle body as
shown. Do not tighten the clamps at this
time. Secure the breather hose to the air
conditioner line using the supplied zip
tie (#15).

First

Second

18. Carefully install the end of the Airaid

Intake Tube (#4) into the hump hose,
and then into the reducer on the throttle
body as shown. Adjust the tube as need­ed, and then tighten the four hose

clamps.

19. Install the Airaid Premium Filter (#1)

on the Quick Fit assembly as shown,
and tighten the hose clamp.

20. Re-align the engine cover with the grom­mets on the engine, and push down firmly
to re-seat the cover.

21. Re-install the oil fill plug.

22. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.

23. Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-458 Airaid Oiled Media 701-458 Airaid SynthaMax Dry Media - Red

702-458 Airaid SynthaMax Dry Media - Black 703-458 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

REV.11.7.13