Installation Instructions
For Part Numbers :
310-178 700-458 Airaid Oiled Media Filter
311-178 701-458 SynthaMax Dry Media Filter - Red
312-178 702-458 SynthaMax Dry Media Filter - Black
313-178 703-458 SynthaMax Dry Media Filter - Blue
2005-2010 Jeep Grand Cherokee
5.7L V8 Hemi
Component Identification
1. Airaid Premium Filter 1
2. Quick Fit Panel 1
3. Quick Fit Panel 1
4. Modular Intake Tube 1
5. Urethane Hump Hose 1
6. Urethane Coupler 1
7. Weather Strip 18” 1
8. #6 Flat Washer 4
9. 6-32 Keps Nut 4
10. 6-32 X 5/16” Screw 4
11. #60 Hose Clamp 4
12. Grommet 1
13. Speed Clamp 1
14. Nylon zip tie 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1.Disconnect The Negative Battery Terminal!
Loosen the hose clamp on air cleaner box lid. Twist and
remove breather hose from air cleaner box lid.
2. Unhook the two air cleaner lid latches on front of
box.
3. Remove the air cleaner box lid by sliding it forward,
and then up, and out of the factory intake tube.
4. Remove factory air filter from air cleaner box.
B.
A.
7. A.) Loosen the hose clamp on the throttle body. B.)
With a 10mm socket, remove the bolt next to the
throttle body that holds the intake resonator in
place.
5. Remove, and set aside the oil filler cap. Use caution
not to drop anything into engine while cap is off.
8. Carefully pull the resonator towards you and rotate
the bottom up to gain access to the tie wrap holding the breather hose to the rubber coupler. Cut
the tie wrap and discard.
6. Carefully lift up on the engine cover (it is held in
place by grommets, no bolts) to a ccess the hose
clamp on the throttle body, and 10mm bolt next to
the throttle body.
9. Slide the clip off of the resonator that holds the
breather tube in place.
10. Carefully twist and remove the temperature sensor
from the bottom of the resonator, and then remove
the resonator from the vehicle.
11. Assemble the two pieces of the Quick Fit panels as
shown, using the four 6-32 screws, washers, and
nuts, that are provided in the kit.
12. Install the weather strip on the top of the Quick
Fit assembly. (Hint: start at one end, and go to-
wards the other end, don’t start in the middle.)
13. Install the Quick Fit assembly in the bottom of the
stock air box by sliding the four tabs on the back
into the slots on the airbox, once installed, re-hook
the two latches. Next, install the speed clamp over
the breather hose and connect it to the Quick Fit
assembly as shown.
16. Install the supplied grommet into the hole in the
back of the tube.
14. Install the hump hose and two #60 hose clamps on
the Quick Fit assembly. Do not tighten the clamps
at this time.
17. Carefully install the temperature sensor into the grommet. Make sure it goes all the way in.
15. Install the coupler and two #60 hose clamps on
the throttle body as shown. Do not tighten the
clamps at this time. Secure the breather hose to
the air conditioner line using the supplied zip tie.
First
Second
18. Carefully install the end of the tube into the hump
hose, and then into the coupler on the throttle
body as shown. Adjust the tube as needed, and
tighten the four hose clamps.
19. Install the Airaid Premium Filter on the Quick Fit
assembly as shown, and tighten the hose clamp.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
20. Realign the engine cover with the grommets on the
engine, and push down firmly to reseat the cover.
21. Reinstall the oil fill plug.
22. Recheck your work, make sure there is no foreign
material in the intake, double check all hose
clamps, screws and nuts for tightness.
23. Reconnect the negative battery cable.
FILTER IDENTIFICATION
700-458 Airaid Oiled Media 701-458 Airaid SynthaMax Dry Media - Red
702-458 Airaid SynthaMax Dry Media - Black 703-458 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!
Synthamax Air Filters do not require oil. Service air
filter as needed by cleaning with common nonpetroleum all-purpose household cleaner and water.
Simple Green®, Formula 409® or equivalent works
great. Apply cleaner to outside of air filter and allow
to soak. Then flush filter clean from the inside out
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
with a garden hose and repeat steps if necessary. Do
not apply high pressure water or air to clean filter.
Allow filter to air dry and reinstall.
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.10.15.13
Loading...