Airaid 310-148 Installation Instructions

Installation Instructions

For Part Numbers:

310-148 720-440 Airaid Oiled Media Filter
311-148 721-440 SynthaMax Dry Media Filter - Red
312-148 722-440 SynthaMax Dry Media Filter - Black
313-148 723-440 SynthaMax Dry Media Filter - Blue

1999-04 Jeep Grand Cherokee

4.7L V8

Component Identification

1. Airaid Premium Filter 1

2. Cool Air Dam 1

3. Tube Adapter 1

4. Modular Intake Tube 1

5. Urethane Hump Hose 1

6. Silicone Reducer Hose 1

7. Weather Strip 28 ½” 1

8. ¼-20 Button Head Bolt 2

9. ¼” Flat Washer 2

10. ¼ Lock Washer 2

11. #52 Hose Clamp 1

12. #56 Hose Clamp 1

13. #60 Hose Clamp 2

14. #16 Black Speed Clamp 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable, and then
loosen both of the hose clamps to factory tube con­necting factory air filter assembly to factory air box
silencer.

2. Remove the factory air filter box lid, accordion
tube, and air filter. (Note: leave factory air filter
base installed in vehicle)

3. Disconnect the breather hose from the factory air
box silencer.

4. Loosen the hose clamp on the throttle body &
both 10mm bolts securing factory air box silencer
to intake manifold. Remove the factory air box
silencer from engine compartment.

Throttle Body

5. Remove the factory air box silencer coupler

from the throttle body.

6. Using the two ¼-20 bolts and washers provided,
fasten the black plastic filter adapter to the Airaid
Cool Air Dam.

7. Position the Airaid Cool Air Dam in place of the
factory air box and snap into place.

8. Slide the urethane hump hose and hose reducer
onto the Modular Intake Tube. Use the two #60
hose clamps on the hump hose and a #56 & #52
hose clamp on the big & small ends of the reducer.

9. Position the Modular Intake Tube assembly to
connect the reducer to the throttle body and the
hump hose to the Airaid Cool Air Dam. (Note:
leave the hose clamps loose until final assembly)

12. Double check your work to be certain that all
nuts, bolts, and clamps are securely fastened.

10. Connect the factory breather hose to the Modu­lar Intake Tube & secure hose with the #16 black
speed clamp provided.

11. Mount the Airaid Premium filter & weather strip
onto the Cool Air Dam. (Hint: start the weather
strip at a corner and work towards the ends).

13. Reconnect the negative battery cable.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-440 Airaid Oiled Media 721-440 Airaid SynthaMax Dry Media - Red

722-440 Airaid SynthaMax Dry Media Filter - Black 723-440 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not require
oil. Service air filter as needed by
cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of air
filter and allow to soak. Then flush
filter clean from the inside out with a
garden hose and repeat steps if nec­essary. Do not apply high pressure
water or air to clean filter. Allow fil­ter to air dry and reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.6.13