Airaid 310-144 Installation Instructions

Installation Instructions

For Part Numbers :

310-144 700-452 Airaid Oiled Media Filter
311-144 701-452 SynthaMax Dry Media Filter - Red
312-144 702-452 SynthaMax Dry Media Filter - Black
313-144 703-452 SynthaMax Dry Media Filter - Blue

1991-95 Jeep Wrangler 4.0L I6
Does Not Fit Vehicles With Optional Anti-Lock
Brakes

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel Black 1

3. Bottom Panel Black 1

4. Brace 1

5. Plastic Intake Tube 1

6. Weather Strip 32” 1

7. Hump Hose 1

8. Coupler 1

9. ½”x10” Hose 1

10. ¼”” Flat Washer 4

11. #6 Flat Washer 5

12. 6-32 Keps Nut 5

13. 6-32 x 5/16” Screw 5

14. ¼-20 x 5/8” Hex Bolt 3

15. ¼-20 Lock Nut 3

16. Grommet 1

17. #44Hose Clamp 2

18. #52 Hose Clamp 2

19. Black Speed Clamp 3

20. Black Speed Clamp 2

21. ¼” Fender Washer 2

22. ¼”NPTx1/2”Barbed Fitting 1

23. 3/8”x4” Hose 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect negative battery cable.
Remove factory valve cover breather
hose from airbox, and valve cover.

2. Unhook vacuum line from airbox,
and remove from vehicle at the can­ister below the master cylinder.
(Save for later use.)

3. Pry open the plastic clamp that
holds the factory intake tube to the
throttle body. Unhook the 3 metal
latches on the airbox that hold it to the
mounting plate, and remove the intake
assembly.

4. Remove the two grommets from the
airbox mounting plate.

5. Using a 10mm socket, remove the
horn bolt. (Save for later use.)

9. Carefully slide the CAD over the
support rod, and then slide the sup­plied grommet over the rod, and into
the hole in the CAD as shown. Rotate
the CAD and place into position on
the factory airbox mount. Reinstall the
radiator support rod, and tighten the
nut.

6. Carefully remove wire loom clamp
from hole in fender.

10. Install two ¼”-20 bolts and wash-
ers thru the top, and fender washers
and nuts on the bottom, where the
factory grommets were removed

7. Assemble the Cool Air Dam as
shown using the 5 screws, washers,
and nuts provided.

11. Slide the CAD bracket under the
horn mount and reinstall the factory
bolt from step 5.

8. Using a 9/16” wrench, loosen the
nut on the radiator rod support, and
lift it up.

A

B

12. A) Using a ¼”-20 bolt, washers,

and nut, bolt the CAD to the fender. B)
Install the wire loom clamp into the
hole in the CAD, as shown.

13. Remove the factory hose from
step 2, and install the new 3/8”x 4”
hose on the end of the vacuum line as
shown. Reinstall vacuum line. (Refer
to step 2.)

14. Install the ¼” barbed fitting into
the intake tube.

15. Install hump hose on CAD with
#52 hose clamps, and the coupler on
the throttle body with #44 hose
clamps as shown.

19. Double check your work, make
sure all nuts, bolts, and clamps are
securely fastened. Make sure there is
no foreign material in the intake
path. Re-connect the negative battery
cable.

16. Slide intake tube into the hump
hose first, and then into the coupler.
Adjust for a good fit, and tighten
hose clamps. Slide vacuum hose on
barbed fitting, and install speed
clamp as shown.

17. Replace the factory breather hose
with ½”x10” rubber hose between
valve cover and intake tube using
speed clamps as shown.

18. Install the Airaid Premium Filter
and the weather strip on the CAD, as
shown. (Hint: start the weather strip
near the radiator support and work
towards the back of the vehicle.)

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-452 Airaid Oiled Media 701-452 Airaid SynthaMax Dry Media - Red

702-452 Airaid SynthaMax Dry Media - Black 703-452 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the

AIRAID Filter Tune-Up Kit!

Synthamax Air Filters do not require
oil. Service air filter as needed by
cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of air
filter and allow to soak. Then flush
filter clean from the inside out with a
garden hose and repeat steps if nec­essary. Do not apply high pressure
water or air to clean filter. Allow fil­ter to air dry and reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.6.13