Airaid 310-136 Installation Instructions

Installation Instructions

For Part Numbers:

310-136 700-450 Airaid Oiled Media Filter
311-136 701-450 SynthaMax Dry Media Filter - Red
312-136 702-450 SynthaMax Dry Media Filter - Black
313-136 703-450 SynthaMax Dry Media Filter - Blue

1991-01 Jeep Cherokee

4.0L I6

Component Identification

1. Airaid Premium Filter 1

2. Right Panel Black 1

3. MAF Panel Black 1

4. 136 Plastic Adapter Tube 1

5. Weather Strip 32 ½” 1

6. 6-32 x 5/16” Screw 4

7. 6-32 Nut 4

8. #6 Flat Washer 4

9. ¼-20 Bolt 2

10. ¼” Lock Washer 2

11. Rubber Cap 1

12. ½” x 7” Hose 1

13. #16 Speed Clamp 2

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

I DISCONNECT NEGATIVE (-) BATTERY CABLE

II Remove Factory Air Box Lid

A) Loosen the factor y intake tube clamp at the air box lid using a flat head screwdr iver . Refer to Fig #1

1991-1995 Models Only:
B) Disconnect the vacuum hose located on the dr iver side rear of the factor y air box. Next disconnect the small vacuum line wher e it at-

taches to the intake manifold. Be careful with the plastic line as it is fragile. It is only moved to enable the install. Refer to Fig #1

C) Disconnect the br eather hose fr om the passenger side of the factor y air box lid. Refer to Fig #1
D) Unclip the factor y air box lid and remove fr om engine compar tment. See Fig #1

III Assemble the Airaid Intake System

A) Mount the black plastic adapter tube onto the Air aid Cool Air Dam and fasten using the two 1/4-20 button head bolts and two lock

washers provided. See Fig #2

B) Assemble the two Air aid Cool Air Dam panels using the small screws, nuts, and washer s pr ovided. See Fig #2

IV Install the Airaid Intake System

A) Position the Air aid Cool Air Dam in place of the or iginal factor y air box lid and snap into place. See Fig #3
B) Connect the factor y tube onto the Air aid plastic tube using the factor y hose clamp. Refer to Fig #3

1991-1995 Models Only:
C) Reattach the small vacuum line to the factor y locations, including the manifold. Replace the shor t factor y hose located on t he plastic

factory tube, with the longer ½”x 7” extension hose and secure on the intake tube nipple using the two #16 black Speed clamps included.

Refer to Fig #3

D) Reattach the br eather hose to the Airaid plastic adapter tube. Refer to Fig #3

1996-2001 Models Only: You do not have the ½” breather line.
E) Plug the nipple on the dr iver ’s side of the Airaid tube with the black r ubber cap pr ovided. Refer to Fig #4

F) Mount the Air aid Pr emium Filt er to the plastic adapter inside the air dam. Refer to Fig #3
G) Pr ess the pr ovided weather seal onto the top r im of the Air aid system. Refer to Fig #3 (Hint: Start at a corner of the air dam for ease

of installation.)

V Finishing Up

A) Inspect over all wor k and check hood clearance.
B) Ensur e that no for eign objects are in the intake path!
C) Re-connect negative battery cable.

Fig#1 Fig#2

Vacuum Line

Breather Hose

Fig#3 Fig#4

To Nipple On Tube

Extension Hose

91-95: Attach Provided 7” Extension
Hose to Plastic Tube. (Shown)

Late 96-01: Plug Nipple on Plastic In­take Tube with Rubber Cap Provided.
(Not Shown)

Factory Breather

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-450 Airaid Oiled Media 701-450 Airaid SynthaMax Dry Media - Red

702-450 Airaid SynthaMax Dry Media - Black 703-450 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the

AIRAID Filter Tune-Up Kit!

Synthamax Air Filters do not require
oil. Service air filter as needed by
cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of air
filter and allow to soak. Then flush
filter clean from the inside out with a
garden hose and repeat steps if nec­essary. Do not apply high pressure
water or air to clean filter. Allow fil­ter to air dry and reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.6.13