Airaid 310-132 Installation Instructions

Advisory Note: Installation of this intake system requires minor modi-

fications be made to the factory air box. Please read through these in­structions in their entirety before beginning the procedure.

Installation Instructions

For Part Numbers:

310-132 700-462 Airaid Oiled Media Filter
311-132 701-462 SynthaMax Dry Media Filter - Red
312-132 702-462 SynthaMax Dry Media Filter - Black
313-132 703-462 SynthaMax Dry Media Filter - Blue

2012-15 Jeep Wrangler

3.6L V6

Component Identification

1. Airaid Premium Filter 1

2. Intake Tube 1

3. Cold Air Box 1

4. Airbox Lid 1

5. Filter Adapter 1

6. Double Hump Hose 1

7. Silicone Reducer 1

8. Airbox Lid Gasket 1

9. Air Scoop Bracket 1

10. 5/8” Hose 7 1/2” long 1

11. 1/4” Flat Washer 13

12. 6mm x 1.0-20 Bolt 2

13. 8-32 x 3/8”Button Head Bolt 2

14. #8 Washer 2

15. #8 Kep nut 2

16. 1/4” Nylock Nut 4

17. 1/4-20 x 5/8” Hex Bolt 4

18. 1/4-20 x 1/2” Button Head Bolt 7

19. #8 Fender Washer 1

20. #8-32 x 1/2 Button Head Bolt 1

21. 3/8-16 Well Nut 3

22. 3/8-16 x 1 1/2” Button Head Bolt 3

23. Engine Cover Grommet 2

24. 3/8 NPT x 5/8 Barbed Fitting 1

25. 1/2” Adel Clamp 2

26. #48 Hose Clamp 1

27. #64 Hose Clamp 1

28. #72 Hose Clamp 2

29. #19 Speed Clamp 2

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

C.

B.

A.

D.

Disconnect The Negative Battery Terminal!

1. Remove the engine cover and set it aside.

2. A.) Disconnect the air temp sensor in the factory

intake. B.) Remove the two 6 mm bolts holding the
intake tube to the fan Shroud. C.) Loosen the Clamps
on both sides of the factory intake tube. D.) Unclip the
coolant line from the intake tube and remove it from the
vehicle.

3. Disconnect the crankcase breather line in the top of the
airbox. Remove the entire airbox as an assembly by un­seating it from the mounting grommets in the inner fender
and lifting upward.

4. Install The Filter Adapter (#5) in the Cold Air Box
(#3) using three 1/4-20 x 1/2” Button Head Bolts (#18)
and 1/4” Flat Washers (#11).

3”

7. Set the factory air scoop on a workbench and mark all
four corners at the three inch mark using a scratch awl.
Using a straight edge and the awl, scribe a line connect­ing all four corners.

5. Install the Air Scoop Bracket (#9) into the Cold Air
Box as shown by using four 1/4-20 x 5/8 Hex Bolts
(#17), 1/4” Flat Washers (#11), and 1/4” Nylock Nuts
(#16).

8. Firmly place the air scoop into a bench vice and cut
along the line created in step 7 using a hack saw or
equivalent.

6. Drill out the rivet heads on the factory airbox and re­move the air scoop.

9. Insert the factory air scoop into the Cold Air Box and
secure it using two 8-32 x 3/8” Button Head Bolts (#13),
#8 Flat Washers (#14), and #8 Kep Nuts (#15).

A

B

10. Replace the factory airbox grommets in the inner

fender area with the three 3/8” Well Nuts (#21).

13. Slide the Double Hump Hose (#6), and two #72
Hose Clamps (#28), onto straight end of the Tube. Slide
the Silicone Reducer (#7) and the #48 and #64 Clamps
on the 90 deg. bend of the Intake tube. Leave the
Clamps loose for now.

11. Mount the Cold Air Box assembly in the inner fender
using the three 3/8” x 1 1/2” Button Head Bolts (#22)

14. Install the Airaid Intake Tube onto the Cold Air Box
and throttle body, align and tighten all four of the
Clamps. Reconnect the air temp sensor.

12. A.) Install the 5/8” Barbed Fitting (#24) into the
threaded 3/8 hole in the side of the Airaid Intake Tube
(#2). B.) Transfer the air temp sensor from the factory
intake into the Airaid Intake Tube and secure it using
the #8-32 x 1/2” Button Head Bolt (#20) and #8 Fender
Washer(#19).

15. Replace the factory breather line with the supplied
5/8” Hose (#10), and connect it to the Barbed Fitting
on the Intake Tube. Secure it using a single Speed
Clamp (#29) on each end.

16. Secure the coolant line to the fan shroud using the
two Adel Clamps (#25), 6 mm Bolts (#12), and 1/4” Flat
Washers (#11).

19. Place the Gasket (#8) onto the underside of the Air
Box Lid (#4) and peel off the protective film. Mount
the lid on the Air Box using four 1/4-20 x 1/2” Button
Head Bolts (#18), and 1/4” Flat washers (#11).

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

17. Replace the factory engine cover grommets with the
larger, Airaid Engine Cover Grommets (#23). Reinstall
the engine cover.

20. Double check your work!

Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.

Double check the hood clearance! Reconnect the nega-

tive battery cable!

18. Install the Airaid Premium Filter (#1) onto the Fil-

ter Adapter.

21. Pre Filter Option: Part Number 799-445

For maximum protection in the harshest environments
Airaid offers a slip on Pre Filter.

- Prolongs Cleaning Intervals

- Water Repellant

- Free Flowing Protection

700-462 Airaid Oiled Media 701-462 Airaid SynthaMax Dry Media - Red

702-462 Airaid SynthaMax Dry Media - Black 703-462 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we suggest
using the AIRAID Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

FILTER IDENTIFICATION

Synthamax Air Filters do not require oil. Service air filter as needed by cleaning
with common non-petroleum all-purpose household cleaner and water. Simple
Green®, Formula 409® or equivalent works great. Apply cleaner to outside of
air filter and allow to soak. Then flush filter clean from the inside out with a gar­den hose and repeat steps if necessary. Do not apply high pressure water or air to
clean filter. Allow filter to air dry and reinstall.

REV.10.02.14