Airaid 301-744 Installation Instructions

INSTALLATION INSTRUCTIONS

#301-744 Airaid Jr. Kit

04-06 Dodge Durango 4.7L

Thank you for purchasing the Airaid MIT or Airaid Jr. Kit. Please read the instruction manual carefully
before proceeding with the installation. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays
for questions regarding fit or instructions that are not clear to you. Your Airaid MIT or Airaid Jr. Kit was
carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any
parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris;
care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS
RESPONSIBILTY!

Thank you for selecting Airaid.

Packing List:

KIT944T Modular Intake Tube 1

851-343 Airaid Premium Filter 1

KITRDCR01 Silicone Hose Reducer 1

KITHUMPHS03 Urethane Hump Hose 1

KIT944HP Hardware & Instructions 1

- KITGRMT03 Rubber Grommet 1

- KITHS52 #52 Hose Clamp 1

- KITHS56 #56 Hose Clamp 1

- KITHS60 #60 Hose Clamp 2

Packing List (cont’d):

Tools Required for this Installation:

Flat Head Screwdriver

10mm Deep Socket

Installation Instructions. Read Me!

1. Disconnect the negative battery

cable and remove the breather
hose from the factory air box lid.

2. Loosen the two hose clamps on

each end of the factory intake
tube.

Unsnap the factory silencer box

3.

from the fan shroud and remove
the factory tube assembly from
the vehicle.

4. Disconnect the factory electrical

connector from the factory air
temperature sensor.

5. Loosen the two 10mm bolts

mounting the factory air box to
the intake manifold and remove
from vehicle.

Turn the air temperature sensor

6.

¼ turn and remove from the air
box. Retain sensor for later use.

7. Install the reducer hose and a #52

hose clamp onto the throttle
body. Install a #56 hose clamp
onto the other side of the reducer.

Hump Hose

8. Slide the urethane hump hose

onto straight end of Airaid intake
tube with two #60 hose clamps.

(Note

: Leave hose clamps loose

until final assembly).

9. Install Airaid intake tube

assembly by connecting the
Airaid hump hose onto the
factory air box lid and the other
end onto the Airaid reducer hose.
Tighten all hose clamps.

10. Install the supplied rubber

grommet and factory air
temperature sensor into the
Airaid intake tube. Then,
reconnect the factory electrical
connector onto the sensor. Lastly,
reconnect the factory breather
hose to the air box lid.

11. If you purchased the Airaid Jr.

Kit P/N 301-744, replace the
factory air filter with the Airaid
Premium Filter included in the
Kit.

12. Double check your work to be

certain that all nuts, bolts, and
clamps are securely fastened.

13. Reconnect the negative battery

cable.

Before

After!

m

Synthamax Air Filters do not require oil. Service air filter as needed by
cleaning with common non-petroleum all-purpose household cleaner and
water. Simple Green®, Formula 409® or equivalent works great. Apply
cleaner to outside of air filter and allow to soak. Then flush filter clean
from the inside out with a garden hose and repeat steps if necessary. Do
not apply high pressure water or air to clean filter. Allow filter to air dry
and reinstall.

Instructions Revision

Date:10/26/10

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.co