Page 1
INSTALLATION INSTRUCTIONS
#301-725 Airaid Jr. Kit
02-07 DODGE RAM 4.7L
Thank you for purchasing the Airaid Modular Intake Tube or Jr. Kit. Please read the instruction manual
carefully before proceeding with the installation. Contact Airaid @ 800-498-6951 8:00 AM – 5:00 PM MST
weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Modular Intake Tube
or Jr. Kit was carefully inspected and packaged. Check that no parts are missing, or were damaged during
shipping. If any parts are missing, contact Airaid.
Thank you for selecting Airaid.
Packing List:
KIT925T Modular Intake Tube 1
851-447 Airaid Premium Filter 1
KITHUMPHS01 Urethane Hump Hose 1
KIT925-1HP Hardware & Instructions 1
- KITHS56 #56 Hose Clamp 1
- KITHS60 #60 Hose Clamp 2
- KITSNP16M4 #16 Speed Clamp 3
- KITGRMT01 Grommet Plug for 2002 1
- KITGRMT02 Grommet 2003-2004 1
- KITHOSE01 ½”x4 ½” Hose 1
- KITELBOW01 90° Plastic Elbow 1
- KIT106CAP Rubber Cap 1
Tools Required for this Installation:
Packing List Cont’d:
Flat Head Screwdriver
10mm Wrench
Page 2
Installation Instructions. Read Me!
m
I DISCONNECT NEGATIVE (-) BATTERY CABLE
II Remove Factory Intake Assembly
a) Loosen and remove the two 10mm bolts holding on the factory intake
assembly.
b) Loosen the clamp on the factory air box lid.
c) Loosen & Remove the fact ory clamp/coupler connecting the factory
intake to the throttle body. (Save clamp/coupler for MIT installation.)
d) Disconnect the crankcase vent hose on the back of the factory air intake
(2002 & 2003 models only).
e) Disconnect ai r temperature sensor wire on back of air intake assembly
(2003 & 2004 models only
f) Unsnap from front of bracket and remove intake assembly.
III Airaid Modular Intake Tube Installation
a) Remove air temperature sensor and save for Airaid tube re-assembly
(2003-2004 models only)
b) For 2002 models
the Airaid tube.
c) For 2003-2004 models
factory air temperature sensor into the grommet. See FIG#2
d) Install black hump hose on Airaid tube & factory air box and secure using
the # 60 hose clamps. See FIG#3
e) Using the #56 hose clamp, slide Airaid tube into the factory throttle body
coupler and secure to the throttle body. See FIG#4
, install rubber grommet plug into the hole on the side of
IV Airaid Jr. P/N 301-725 Replacement Filter
a) If you purchased the Airaid Jr. kit P/N 301-725, replace the factory air filter with
the Airaid Premium Filter included in the Airaid Jr. kit.
V Re-Connect Accessories
a) Re-connect air temperature sensor wire.
2002-2003 Models:
b) Using the 90° plastic elbow provided, connect the factory crankcase vent
hose with the 4 ½” hose to the Airaid tube. See Fig#5
c) Secure the hose and elbow with the 3 black speed clamps provided. See
Fig#5
2004 And Later Models:
d) Slide provided rubber cap over the nipple at the throttle body end of the
MIT Tube. See Fig#6
e) Re-connect negative battery cable.
Synthamax Air Filters do not
with common non-petroleum all-purpose household cleaner and water. Simple
Green®, Formula 409® or equivalent works great. Apply cleaner to outside of air
filter and allow to soak. Then flush filter clean from the inside out with a garden
hose and repeat steps if necessary. Do not apply high pressure water or air to clean
filter. Allow filter to air dry and reinstall.
). See FIG#1
, install rubber grommet w/thru hole and insert the
require oil. Service air filter as needed by cleaning
Fig#1
Fig#2
Fig#3
Fig#4
Fig#5
Fig#6
Rev. 10/26/10
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.co
Loading...