Airaid 300-725 Installation Instructions

INSTALLATION INSTRUCTIONS

#300-925-1 Modular Intake Tube

OR

#300-725 Airaid Jr. Kit

02-07 DODGE RAM 4.7L

Thank you for purchasing the Airaid Modular Intake Tube or Jr. Kit. Please read the instruction manual
carefully before proceeding with the installation. Contact Airaid @ 800-498-6951 8:00 AM – 5:00 PM MST
weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Modular Intake Tube
or Jr. Kit was carefully inspected and packaged. Check that no parts are missing, or were damaged during
shipping. If any parts are missing, contact Airaid.

Thank you for selecting Airaid.

Packing List:

KIT925T Modular Intake Tube 1

850-447 Airaid Premium Filter 1

KITHUMPHS01 Urethane Hump Hose 1

KIT925-1HP Hardware & Instructions 1

- KITHS56 #56 Hose Clamp 1

- KITHS60 #60 Hose Clamp 2

- KITSNP16M4 #16 Speed Clamp 3

- KITGRMT01 Grommet Plug for 2002 1

- KITGRMT02 Grommet 2003-2004 1

- KITHOSE01 ½”x4 ½” Hose 1

Packing List Cont’d:

- KITELBOW01 90° Plastic Elbow 1

- KIT106CAP Rubber Cap 1

Tools Required for this Installation:

Flat Head Screwdriver

10mm Wrench

m

Installation Instructions. Read Me!

I DISCONNECT NEGATIVE (-) BATTERY CABLE
II Remove Factory Intake Assembly

a) Loosen and remove the two 10mm bolts holding on the factory intake

assembly.

b) Loosen the clamp on the factory air box lid.
c) Loosen & Remove the factory clamp/coupler connecting the factory

intake to the throttle body. (Save clamp/coupler for MIT installation.)

d) Disconnect the crankcase vent hose on the back of the factory air intake

(2002 & 2003 models only).

e) Disconnect air temperature sensor wire on back of air intake assembly

(

2003- 2007models only). See FIG#1

f) Unsnap from front of bracket and remove intake assembly.

III Airaid Modular Intake Tube Installation

a) Remove air temperature sensor and save for Airaid tube re-assembly

(2003-2007 models only)

b) For
c) For
d) Install black hump hose on Airaid tube & factory air box and secure using
e) Using the #56 hose clamp, slide Airaid tube into the factory throttle body

IV Airaid Jr. P/N 300-725 Replacement Filter

a) If you purchased the Airaid Jr. kit P/N 300-725, replace the factory air filter with
the Airaid Premium Filter included in the Airaid Jr. kit.

V Re-Connect Accessories

a) Re-connect air temperature sensor wire.

2002-2003 Models:

b) Using the 90° plastic elbow provided, connect the factory crankcase vent
c) Secure the hose and elbow with the 3 black speed clamps provided. See

2004 And Later Models:

d) Slide provided rubber cap over the nipple at the throttle body end of the

e) Re-connect negative battery cable.

2002 models, install rubber grommet plug into the hole on the side of

the Airaid tube.

2003-2007 models, install rubber grommet w/thru hole and insert the

factory air temperature sensor into the grommet. See FIG#2

the # 60 hose clamps. See FIG#3

coupler and secure to the throttle body. See FIG#4

hose with the 4 ½” hose to the Airaid tube. See Fig#5

Fig#5

MIT Tube. See Fig#6

Rev. 10/11/10

Fig#1

Fig#2

Fig#3

Fig#4

Fig#5

Fig#6

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.co