Airaid 300-283 Installation Instructions

Installation Instructions

For Part Numbers :

300-283 720-476 Airaid Oiled Media Filter
301-283 721-476 SynthaMax Dry Media Filter - Red
302-283 722-476 SynthaMax Dry Media Filter - Black
303-283 723-476 SynthaMax Dry Media Filter - Blue

2013-2015 Ram 1500 3.6L V6

Component Identification

1. Airaid Premium Filter 1

2. Cool Air Box 1

3. Filter Adapter 1

4. Weather Strip 32.5” 1

5. Adapter Gasket 1

6. 1/4” Flat Washer 3

7. ¼-20 x 1/2” Button Head Screw 3

8. 1/4" NPT Plug 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1.Disconnect The Negative Battery Terminal!
Loosen one hose clamp at each end of the air intake tube
and remove it from the vehicle.

2. Remove the two fender bolts in the air box cradle.
The bolts will be reused in step #10

3. Rock the air box back and forth as you are lifting it
straight up to remove it from the vehicle. It is only held in
by grommets.

4. Remove and save four grommets from the bottom of
the factory air box. They will be reused in step #5

X

5. Transfer the 4 factory air box grommets into the

Airaid Cool Air Box as shown. Note: Two of the holes
do not receive grommets.

X

6. Transfer the scoop from the factory air box into the

Airaid Cool Air Box as shown.

7. Prepare the Filter Adapter (#3 ) for installation by
mating it to the Adaptor Gasket (# 5) and aligning the
bolt holes.

8. Mount the Filter Adapter and Gasket inside the Cool
Air Box as shown using the three sets of 1/4-20 Button
Head Screws (# 7) and 1/4” Flat Washers (#6).

9. Install the 1/4” Plug (#8) into the Cool Air Box snout
as shown.

10. Set the Airaid Cool Air Box into the cradle and se­cure it using the factory hardware removed in step #2.

13. Double check your work!

Make sure there is no foreign material in the intake path.
Make sure all clamps, hoses, bolts, and screws are tight.
Double check the hood clearance!

Reconnect the negative battery cable!

11. Reinstall the factory air intake tube and tighten the

two hose clamps.

12. Install the Airaid Premium Filter onto the Filter
Adapter inside the Cool Air Box. Install the Weather­strip onto the Cool Air Box as shown, with the contour
rolling away from the Filter.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-476 Airaid Oiled Media 721-476 Airaid SynthaMax Dry Media - Red

722-476 Airaid SynthaMax Dry Media - Black 723-476 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a
garden hose and repeat steps if neces­sary. Do not apply high pressure water
or air to clean filter. Allow filter to air
dry and reinstall.

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.01.13.15