Page 1
Installation Instructions
For Part Numbers:
300-254 700-469 Airaid Oiled Media Filter
301-254 701-469 SynthaMax Dry Media Filter - Red
302-254 702-469 SynthaMax Dry Media Filter - Black
303-254 703-469 SynthaMax Dry Media Filter - Blue
2010-12 Dodge Ram 6.7L I6
Cummins Diesel
Component Identification
1. Airaid Premium Filter 1
2. Airaid Intake Tube 1
3. Cool Air Box 1
4. Filter Adapter 1
5. Urethane Hump Hose 1
6. Weather Strip 26 1/2” 1
7. 8/32 x 1/2” Button Head Screw 3
8. #8 Flat Washer 3
9. 1/4-20 Button Head Bolt 3
10. ¼” Flat Washer 3
11. 5/16-18 x 3/4” Hex Head Bolt 1
12. 5/16” Flat Washer 1
13. 5/16” Flange Nut 1
14. 3/8-16 Well Nut 2
15. 3/8-16 x 1 1/2” Button Head 2
16. 3/8” Flat Washer 2
17. #72 Hose Clamp 2
18. # 193 Bracket 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
B.
A.
A.
1. Disconnect the negative battery cables.
A) Discon nect the a ir sensor s on t he upper ha lf of
the Factory Airbox, and detach the wire harness. B)
Loosen the hose clamp that secures the factory intake
tube assembly to the Airbox, unclip the Airbox lid,
and remove the upper half of the factory airbox from
the vehicle.
2. Using a 10 mm socket, remove the nut that secures
the factory airbox, lower half, to the radiator support .
Rock the factory airbox assembly side to side to release it from it’s mounting grommets, and remove it
from the vehicle.
3. Loosen the hose clamp that secures the factory intake tube assembly to the rubber elbow on the turbo
inlet, and remove the assembly from the vehicle..
4. Remove the two Factory Airbox grommets and set
aside. They will not be reused.
7. Install the Two supplied well nuts (#14) into the
factory airbox mounting holes as shown.
5. Using a 13mm socket remove one bolt that secures
the fan shroud to the radiator on the passenger side of
the vehicle.
8. Install the filter adapter (#4) into the Cool Air Box,
(CAB),(#3) using t hr ee 1/4” But ton Head b olts (#9)
and flat washers (#10) as shown.
6. Install the bracket (#18) onto the radiator shroud as
shown using the factory hardware. Leave the bolt
slightly loose for now.
B.
A.
9. Install the CAB into the vehicle as shown. A.) In-
stall the 3/8” button head bolts (#15) and flat washer
(#16) thru the CAB and into the well nuts. B.) Install
the 5/16” bolt (#11) flat washer (#12), and flange nut
(#13) thru the CAB and L-bracket. Tighten all mounting bolts at this time.
Page 2
B
A
10. Install the supplied hump hose (#5) onto the filter
adapter using two #72 hose clamps (#17). Leave the
clamps loose for now.
11. A) Inst all the Air a id Intake Tube (#2) into the
factory turbo elbow and then into the hump hose. Adjust for fit, and then tighten all three hose clamps. Reinstall the intake temperature sensor and Mass Air
Flow sensor into the Airaid Intake Tube using three 832 button head screws (#7) and #8 flat washers (#8).
Do Not Use The Factory Screws! B) Reinstall the
factory wiring harness anchor into the hole in the
Airaid Intake Tube.
12. Install the Airaid Premium Filter (#1) onto the
filter adapter and tighten the clamp. Install the weather
strip onto the top of the CAB starting at the right fender and working your way towards the radiator.
13. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.
14. Reconnect the negative battery cables!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.
700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red
702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
FILTER IDENTIFICATION
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a garden hose and repeat steps if necessary. Do
not apply high pressure water or air to
clean filter. Allow filter to air dry and reinstall.
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.10.22.13
Loading...