Page 1
Installation Instructions
For Part Numbers:
300-236 720-476 Airaid Oiled Media Filter
301-236 721-476 SynthaMax Dry Media Filter - Red
302-236 722-476 SynthaMax Dry Media Filter - Black
303-236 723-476 SynthaMax Dry Media Filter - Blue
2009-12 Dodge Ram 1500/2500/3500
5.7L V8
Component Identification
1. Airaid Premium Filter 1
2. Cool Air Box 1
3. Filter Adapter 1
4. 1/2” x 22” Breather Hose 1
5. Weather Strip 33” 1
6. 1/4-20 X 5/8” Hex Bolt 3
7. 1/4” Flat Washer 3
8. 1/2” x 90° Elbow 1
9. 1/4”NPT x1/2” Barbed Fitting 1
10. 1/2” x 3/4” Barbed Connector 1
11. 1/2” x 1/2” Barbed Connector 1
12. Adapter Gasket 1
13. 1/4 Hex Plug (NOT USED) 1
14. 3/4” Breather Hose (NOT USED) 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
Temperature Sensor
1. Disconnect the negative battery cable!
Locate the temperature sensor on the air intake
tube, slide the red tab, squeeze the black tab on the
electrical connector, and then disconnect the temperature sensor from the air intake tube. Disconnect the crankcase breather tube from the air filter
box. Loosen one hose clamp at each end of the air
intake tube and remove it from the vehicle.
2. Lift up the front of the engine beauty cover, and
then pull it towards you to remove it from the vehicle. It is only held in position by rubber grommets.
3. Using a 13mm socket, remove the two bolts that
hold the air cleaner mount to the inside right fender. Save them for reinstallation in step #9.
4. Rock the airbox back and forth as you are lifting it straight up to remove it from the vehicle. It is
only held in by grommets.
Gasket
Filter Adapter
7. Install the adapter gasket (#12) and filter adapter
(#3) into the CAB using three 1/4-20 x 5/8” bolts
(#6) and flat washers (#7) as shown. Refer to the
line drawing above for reference.
5. Remove and save three grommets from the bottom of the factory airbox. They will be reused in
step #6.
Fitting
1/4” Bolts From Step #7
8. Install the 1/4” NPT x 1/2” barbed fitting (#9)
into the filter adapter as shown.
6. Install the three grommets removed in step #5
into the bottom of the Airaid Cool Air Box (CAB)
(#2) at the locations shown here.
9. Install the CAB into the vehicle by aligning the
grommets over the locating pins on the factory airbox mount. Reinstall the factory bolts into the fender that were removed in step #3.
Page 2
Factory Elbow
Barbed Fitting
1/2” Hose
10. Install the supplied 1/2” x 3/4” plastic reduc-
ing coupler (#10), into the factory rubber elbow
next to the oil fill neck as shown, and then connect
the supplied 1/2” x 22” hose (#4) to the coupler.
13. Reinstall the factory air intake tube. Reconnect
the electrical connector to the temperature sensor,
and then tighten both hose clamps.
Coupler
1/2” x 3/4”
1/2” x 1/2”
Rubber Elbow
11. Install the supplied 1/2” x 1/2” plastic coupler
(#11) into the 1/2” hose from step #10. Next connect the 1/2” rubber elbow (#8) between the 1/2”
connector and the barbed fitting on the filter adapter.
14. Install the Airaid Premium Filter (#1) onto the
filter adapter and tighten the clamp. Next install
the weather strip (#5) on the top of the CAB as
shown. (Hint: Start at one end of the CAB and
work your way towards the other end.)
Coupler
12. Reinstall the factory beauty cover making sure
that the grommets are aligned with the grommet
posts and that the crankcase breather hose is
aligned in the slot on the side of the cover.
15. Double check your work!
Make sure there is no foreign material in
the intake path. Make sure all clamps, hoses, fasteners, and wiring connections are
tight.
16. Reconnect the negative battery
cable!
Discard parts # 13 and 14. They
are not used on this application.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.
FILTER IDENTIFICATION
720-476 Airaid Oiled Media 721-476 Airaid SynthaMax Dry Media - Red
722-476 Airaid SynthaMax Dry Media - Black 723-476 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a garden hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.10.14.13
Page 3
Installation Instructions
For Part Numbers:
300-236 720-476 Airaid Oiled Media Filter
301-236 721-476 SynthaMax Dry Media Filter - Red
302-236 722-476 SynthaMax Dry Media Filter - Black
303-236 723-476 SynthaMax Dry Media Filter - Blue
2003-08 Dodge Ram 1500/2500/3500
3.7L, 4.7L, 5.7L
2009-12 Dodge Ram 1500
4.7L
Component Identification
1. Airaid Premium Filter 1
2. Cool Air Box 1
3. Filter Adapter 1
4. Weather Strip 33” 1
5. 1/4-20 X 5/8” Hex Bolt 3
6. 1/4” Flat Washer 3
7. 1/2” x 90° Elbow 1
8. 1/4”NPT x1/2” Barbed Fitting 1
9. 1/2” x 3/4” Barbed Connector 1
10. 1/4”NPT Hex Plug 1
11. 3/4” x 2 1/2” Breather Hose 1
12. Adapter Gasket 1
13. 22” Breather hose (NOT USED) 1
14. 1/2”Connector (NOT USED) 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1. Disconnect the negative battery cable!
Loosen the two hose clamps on the flexible intake
tube, one at the airbox lid and one at the resonator.
Slide the flexible tube off of the lid and the resonator and remove it from the vehicle.
2004-and later Models: Disconnect the crank-
case breather hose that attaches to the factory air-
2. Rock the airbox back and forth as you are lifting
it straight up to remove it from the vehicle. It is
only held in by grommets.
3. Remove and save three grommets from the bottom of the factory airbox. They will be reused in
step #4.
Gasket
4. Install the three grommets removed in step # 3
into the bottom of the Airaid Cool Air Box (CAB)
(#2) at the locations shown here.
Fitting
1/4” Bolts From Step #7
7. Install the 1/4” NPT x 1/2” barbed fitting (#8)
into the filter adapter as shown.
2003 Models: Install the 1/4”NPT plug (#10) in
place of the barbed fitting.
5. Using a 13mm socket, remove the two bolts that
hold the airbox mount to the inside right fender.
Save them for reinstallation in step #8.
8. Install the CAB into the vehicle by aligning the
grommets over the locating pins on the factory airbox mount. Reinstall the factory bolts thru the CAB
and into the fender that were removed in step #4.
Filter Adapter
6. Install the adapter gasket (#12) and filter adapter
(#3) into the CAB using three 1/4-20 x 5/8” bolts
(#5) and flat washers (#6) as shown. Refer to the
line drawing above for reference.
9. Reinstall the factory air intake tube and tighten
the two hose clamps.
Remove the rubber hose from the end of the factory
crankcase breather tube.
Page 4
Rubber Elbow
3/4” x 2 1/2” Hose
1/2” x 3/4”
Coupler
12. Double check your work!
Make sure there is no foreign material in
the intake path. Make sure all clamps, hoses, fasteners, and wiring connections are
tight.
13. Reconnect the negative battery
cable!
10. Install the supplied 3/4” x 2 1/2” hose (#11)
onto the factory crankcase breather tube, and then
insert the 1/2” x 3/4” barbed connector (#9) into the
3/4” hose. Next connect the 1/2” rubber elbow (#7)
from the 1/2” barbed fitting on the filter adapter to
the 1/2” x 3/4” connector. See the line drawing on
the front page for reference.
2004-and later Models: Inser t the 1/2” x 3/4”
connector into the factory breather hose and then
install the rubber elbow between the two 1/2”
barbed fittings, similar to what is shown above.
11. Install the Airaid Premium Filter (#1) onto the
filter adapter and tighten the clamp. Next install the
weather strip (#4) on the top of the CAB as shown.
(Hint: Start at one end of the CAB and work your
way towards the other end.)
Discard parts # 13 and 14. They
are not used on this application.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.
720-476 Airaid Oiled Media 721-476 Airaid SynthaMax Dry Media - Red
722-476 Airaid SynthaMax Dry Media - Black 723-476 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
FILTER IDENTIFICATION
Synthamax Air Filters do not require oil. Service
air filter as needed by cleaning with common nonpetroleum all-purpose household cleaner and water. Simple Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of air filter
and allow to soak. Then flush filter clean from the
inside out with a garden hose and repeat steps if
necessary. Do not apply high pressure water or
air to clean filter. Allow filter to air dry and reinstall.
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.10.15.13
Loading...