
Installation Instructions
For Part Numbers:
300-192 700-445 Airaid Oiled Media Filter
301-192 701-445 SynthaMax Dry Media Filter - Red
302-192 702-445 SynthaMax Dry Media Filter - Black
303-192 703-445 SynthaMax Dry Media Filter - Blue
2006-08 Dodge Ram 1500/2500/3500
3.7L V6, 4.7L V8, 5.7L V8
Component Identification
1. Airaid Premium Filter 1
2. Cool Air Dam 1
3. Weather Strip 32 3/4” 1
4. Speed Clamp 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1. Disconnect the negative battery cable!
Disconnect the factory breather hose from the air cleaner lid.
2. Unlatch 4 clips that hold down the factory airbox lid.
Loosen the hose clamp on the factory intake tube where it
connects to the airbox lid, then remove the lid.
3. Remove the factory air cleaner. 4. Install the Quick Fit Panel (#2) by slipping it into the factory intake tube, and then sliding it over the tabs on the factory airbox base. Adjust it for fit on top of the airbox base, and
re-latch the 4 clips to hold the Quick Fit Panel securely in
place.

5. Slide the factory intake tube all the way onto the Quick Fit
Panel tube and tighten the hose clamp. Slip the #24 speed
clamp(#4) over the factory breather hose and re-connect the
factory breather hose to the nipple on the Quick Fit Panel.
Squeeze the speed clamp to secure the breather hose.
6. Install the Airaid Premium Filter (#1) onto the tube of the
Quick Fit Panel as shown, and tigh ten the hose clamp.
Now install the weather strip (#3) on top of the Quick Fit
Panel. (Hint: Start with the end of the weather strip at one
corner, and work your way around to the other corner.)
7. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps and hoses are tight.
8. Reconnect the negative battery cable!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
700-445 Airaid Oiled Media 701-445 Airaid SynthaMax Dry Media - Red
702-445 Airaid SynthaMax Dry Media - Black 703-445 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
FILTER IDENTIFICATION
Synthamax Air Filters do not require oil. Service air filter as needed by cleaning with common nonpetroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.11.5.13