Airaid 300-191 Installation Instructions

Installation Instructions

For Part Numbers:

300-191 700-445 Airaid Oiled Media Filter
301-191 701-445 SynthaMax Dry Media Filter - Red
302-191 702-445 SynthaMax Dry Media Filter - Black
303-191 703-445 SynthaMax Dry Media Filter - Blue

2006-07 Dodge Ram 1500

4.7L V8 (With Hood Mat)

Component Identification

1. Airaid Premium Filter 1

2. Cool Air Dam 1

3. Modular Intake Tube 1

4. Urethane Hump Hose 1

5. Weather Strip 32 3/4” 1

6. #56 Hose Clamp 1

7. #60 Hose Clamp 2

8. #14 Speed Clamp 1

9. #24 Speed Clamp 1

10. Rubber Grommet 1

11. Black Rubber Cap 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable!
Loosen the hose clamp on the resonator. Dis­connect the breather hose going into the facto­ry airbox lid.

2. Unlatch 4 clips on the factory airbox lid and
remove the lid and intake hose assembly. Re­move the factory air filter.

3. Squeeze the tab on the connector, and dis­connect the air intake temperature sensor on
the back of the resonator.

4. With a 10mm socket, remove two bolts hold­ing the intake resonator to the intake manifold
brackets.

7. Install the supplied grommet (#10) into the
Modular Intake Tube (#3). Next, carefully slide
the factory temperature sensor into the grom­met until it touches the tab on the temperature
sensor.

5. Lift the front of the resonator straight up, and
then pull towards you to remove it from the
vehicle.

8. Install the Cool Air Dam (#2) onto the factory
airbox base by sliding the tabs on the base thru
the CAD and then adjust the sides to fit. Re­latch the 4 clips to hold the CAD securely in
place.

6. Gently twist the air temperature sensor
counterclockwise and remove it from the
resonator.

9. Install the urethane hump hose (#4) onto
the tube on the CAD using two #60 hose
clamps (#7). Leave clamps loose.

10. Install a #56 hose clamp (#6) on the facto­ry throttle body coupler. Leave loose for now.

11. Install the Modular Intake Tube (#3) into
the hump hose first and then into the factory
coupler. Adjust for fit, and then tighten all 3
hose clamps.

12. Install the provided #24 speed clamp
(#9) over the factory breather hose, then
slide the hose onto the nipple on the CAD.
Squeeze the clamp to secure the hose.

13. Re-connect the wiring harness to the fac-
tory temperature sensor on the back of the
Modular Intake Tube (#3).

14. Install the provided rubber cap (#11), and
speed clamp (#8) onto the nipple on the Modular
Intake Tube (#3).

15. Install the Airaid Premium Filter (#1)
onto the tube on the CAD and tighten the
hose clamp. Next install the weather strip
(#5) on the top of the CAD as shown. (Hint:

Start at one corner and work towards the
other corner. Don’t start in the middle.)

16. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, and wiring connections are tight.

17. Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.

700-445 Airaid Oiled Media 701-445 Airaid SynthaMax Dry Media - Red

702-445 Airaid SynthaMax Dry Media - Black 703-445 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray

FILTER IDENTIFICATION

Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.

P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.5.13