Airaid 300-165 Installation Instructions

Installation Instructions

For Part Numbers:

300-165 720-440 Airaid Oiled Media Filter
301-165 721-440 SynthaMax Dry Media Filter - Red
302-165 722-440 SynthaMax Dry Media Filter - Black
303-165 723-440 SynthaMax Dry Media Filter - Blue

2005-11 Dodge Dakota
2006-09 Mitsubishi Raider

3.7L V6, 4.7L V8

Component Identification

1. Airaid Premium Filter 1

2. Quick Fit Panel 1

3. Weather Strip 28” 1

4. #24 Speed clamp 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

B.

2007 and newer
models: 3 clips only

1. Disconnect the negative battery cable.

Unlatch the four clips (three on 2007 and newer models) on the
factory airbox.

2. A.) Loosen the hose clamp on the factory airbox lid.
B.) Disconnect the breather hose from the factory airbox lid.

A.

3. Remove the factory airbox lid and air filter from the airbox

base.

B.

A.

4. 2007 and newer models only: A.) Using a flat blade

screwdriver, gently pry and remove one factory clip from
the passenger side rear of the airbox base. (see arrow above)
B.) Re-install the clip onto the rear of the factory airbox
base (see arrow above).

5. Slip the five tabs of the Quick fit panel (#2) through the slots on
the airbox base. Adjust the panel for fit, then re-latch two of the
factory clips onto the panel.

6. Slide the factory intake tube onto the Quick Fit Panel and
tighten the hose clamp.

7. Re-connect the factory breather hose onto the Quick Fit Pan-
el and secure with the #24 speed clamp (#4) as shown.

8. Install the Airaid Premium Filter (#1) onto the Quick Fit
Panel as shown, and tighten the clamp. Install the weather
strip (#3) onto the top of the Quick Fit Panel as shown. (Hint:
Start at one end and work towards the other.)

9. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.

10. Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

720-440 Airaid Oiled Media 721-440 Airaid SynthaMax Dry Media - Red

722-440 Airaid SynthaMax Dry Media - Black 723-440 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

FILTER IDENTIFICATION

Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.4.13