Airaid 300-151 Installation Instructions

Installation Instructions

For Part Numbers:

300-151 720-440 Airaid Oiled Media Filter
301-151 721-440 SynthaMax Dry Media Filter - Red
302-151 722-440 SynthaMax Dry Media Filter - Black
303-151 723-440 SynthaMax Dry Media Filter - Blue

2000-04 Dodge Dakota
2000-03 Dodge Durango

4.7L V8

Component Identification

1. Airaid Premium Filter 1

2. Cool Air Dam Assembly 1

3. Modular Intake Tube 1

4. Urethane Hump Hose 1

5. Weather Strip 26 1/4” 1

6. #16 Speed Clamp 2

7. #56 Hose Clamp 2

8. Grommet Plug 1

9. Grommet w/Thru Hole 1

10. ½” x 6” rubber hose 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect negative battery cable
and loosen the intake tube clamp.

2. Disconnect the crankcase breath­er tube at the air box lid.

3. Unclip the factory air box lid and
remove the lid and factory air filter
from vehicle.

4. If your vehicle is equipped with
an air temperature sensor, discon­nect and remove the sensor & re­tain for later installation with
Airaid kit.

1 of 2 10mm Bolts

Remove Factory
Assembly

5. Loosen and remove the two

10mm bolts below the silencer
box.

9. Press the weather seal onto the top
of the Airaid Cool Air Dam. (Hint:
begin at a corner and work the
weather strip towards the ends)

6. Loosen the hose clamp on the
throttle body & remove the silenc­er box & accordion style tube from
vehicle.

10. Install the urethane hump hose
onto larger end of the Airaid In­take tube using the # 56 hose
clamp provided.

7. Mount the Airaid Cool Air Dam in
place of the original air box lid &
snap into place.

11. Reinstall factory throttle body
coupler onto smaller end of intake
tube.

8. Mount the Airaid Premium filter
inside the Cool Air Dam and secure
with hose clamp provided.

12. Slide the intake tube into the
throttle body & align hump hose
with Airaid Cool Air Dam. Slide the
hump hose over end of the Airaid
Cool Air Dam intake and secure us­ing a #56 hose clamp.

13. Factory coupler must be orientat­ed with the clamp screw at the 12
o’clock position.

Provision for Some ‘03
and ‘ 04 Models

14. If your vehicle is equipped

with an air temperature sensor,
insert the rubber grommet into the
hole on the intake tube and mount
the air temperature sensor into the
grommet.

15. If your vehicle is not equipped
with an air temperature sensor, in­sert the rubber grommet plug into
the hole on the intake tube.

16. Reconnect the crankcase
breather hose to the tube on the
Airaid Cool Air Dam and secure
with the black speed clamp provid­ed. (Note for 2004: Replace breath­er hose with new ½” ID hose and
speed clamps provided.)

17. If your vehicle is equipped with a
dipstick tube that interferes with the
location of the Airaid Intake System,
an adjustment to the dipstick tube
must be made. Firmly grasp the dip­stick tube about 6 inches below the
top with your left hand and carefully
form the tube towards the engine.
This will allow for clearance of the
Airaid Intake System.

18. Double check your work to be certain
that all nuts, bolts, and clamps are secure-

19. Reconnect the negative battery cable.

ly fastened.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM ­5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid
Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged
during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct ex­posure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS
THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

720-440 Airaid Oiled Media 721-440 Airaid SynthaMax Dry Media - Red

722-440 Airaid SynthaMax Dry Media - Black 723-440 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

FILTER IDENTIFICATION

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.1.13