Installation Instructions
For Part Numbers :
300-150 700-445 Airaid Oiled Media Filter
301-150 701-445 SynthaMax Dry Media Filter - Red
302-150 702-445 SynthaMax Dry Media Filter - Black
303-150 703-445 SynthaMax Dry Media Filter - Blue
2003-05 Dodge Ram 1500/2500/3500
5.7L V8
Component Identification
1. Airaid Premium Filter 1
2. Cool Air Dam 1
3. Weather Strip 33 ¼” 1
4. Modular Intake Tube 1
5. Urethane Hump Hose 1
6. Urethane Coupler 1
7. #16 Speed Clamp 2
8. #19 Speed Clamp 1
9 #22 Speed Clamp 2
10. #24 Speed Clamp 1
11. Black Rubber Cap Large 1
12. Black Rubber Cap Small 1
13. #60 Hose Clamp 4
14. Rubber Grommet 1
15. ½” x 4 ½” Hose 1
16. Black Connector Fitting 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1. Disconnect the negative battery
cable, and remove the factory
“accordion” style intake hose by
loosening the two factory clamps.
2. Loosen the two 10mm bolts securing the factory resonator to the intake
manifold.
3. Disconnect the air temperature
sensor connector on the front of the
factory resonator. Next, twist the
temperature sensor and remove it
from the factory intake resonator.
(Retain for later use with Airaid intake).
4. 2003 Models: Disconnect &
remove the crankcase vent hose
from the front of the factory resonator.
5. 2004-05 Models: disconnect
breather hose from factory air box
lid.
9. Mount the Airaid Premium filter
inside the Cool Air Dam & secure
with hose clamp provided.
6. Remove the factory resonator and
rubber seal from throttle body.
10. 2003 Models Only: Slip the
black rubber cap over the nipple on
the Cool Air Dam and secure using
the #19 black speed clamp provided.
7. Unclip & remove the factory air
box lid and factory air filter.
11. 2004-05 Models Only: Mount
factory breather hose to the nipple on
the Cool Air Dam and secure using
the #24 black speed clamp provided.
8. Position the Airaid Cool Air Dam
in place of the original air box lid.
Snap in place.
12. Install the rubber grommet into
the hole on the back side of the
Airaid tube & insert the factory air
temp sensor into grommet.
13. Install the urethane hump
hose on the long end of the
Airaid tube using two of the #60
hose clamps provided. Leave
loose for final assembly.
14. Slide the urethane coupler onto
the throttle body and secure using
a #60 hose clamp provided & install the 2nd #60 hose clamp on
the other end of the coupler, leave
loose for final assembly.
15. Slide the Airaid tube with hump
hose into the Airaid Cool Air Dam
first, and then slide the other end into
the throttle body coupler. (Note:
The Airaid tube should be flush
against throttle body with a gap between the tube and Cool Air Dam
assembly for engine movement.)
After inspection, adjust the Airaid
tube, coupler, and hump hose and
tighten all hose clamps
16. Re-connect air temperature sen-
sor connector.
20. Check for any foreign objects or debris in the intake path.
21. Double check your work to
be certain that all nuts, bolts,
and clamps are securely fastened.
17. 2003 Models Only: Use the
plastic barbed fitting and ½” hose
provided; connect factory vent hose
to Airaid intake tube & secure the
½” hose with (2) #16 black speed
clamps provided. Secure factory
vent hose with (2) #22 black speed
clamps provided.
18. 2004-05 Models Only: Slide the
black rubber cap over the nipple near
the throttle body end of the Airaid
Tube.
19. Install weather strip along the
top rim of the Airaid Intake System. (Hint: start the install at the
top corner of the cold air dam)
22. Reconnect the negative battery cable.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-445 Airaid Oiled Media 701-445 Airaid SynthaMax Dry Media - Red
702-445 Airaid SynthaMax Dry Media - Black 703-445 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning with
common non-petroleum all-purpose household cleaner and water. Simple Green®,
Formula 409® or equivalent works great.
Apply cleaner to outside of air filter and
allow to soak. Then flush filter clean from
the inside out with a garden hose and repeat steps if necessary. Do not apply high
pressure water or air to clean filter. Allow
filter to air dry and reinstall.
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.11.1.13
Loading...