Airaid 250-315 Installation Instructions

Installation Instructions

For Part Numbers:

250-315 700-469 Airaid Oiled Media Filter
251-315 701-469 SynthaMax Dry Media Filter - Red
252-315 702-469 SynthaMax Dry Media Filter - Black
253-315 703-469 SynthaMax Dry Media Filter - Blue

2014 Chevrolet SS

6.2L V8

Component Identification

1. Airaid Premium Filter 1

2. Cool Air Dam 1

3. Filter Adapter 1

4. Adapter Coupler 1

5. 1/4” Flat Washer 3

6. ¼-20 x 1/2” Button Head Screw 3

7. #68 Hose Clamp 1

8. Weatherstrip 28 1/2” 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1.Disconnect the negative battery terminal.

Depress the three locking tabs on the positive terminal
cover and remove it.

2. Disconnect the Mass Air Flow sensor and loosen the
intake tube clamp.

3. Remove the two 6mm flange nuts securing the air box
assembly to the inner fender.

4. Separate the intake tube from the Mass Air Flow sen­sor and remove the entire air box assembly from the
vehicle.

Post Grommet

Grommets and Sleeves

7. Transfer the OEM grommets and steel sleeves from

the factory air box, into the Air Dam assembly as
shown. The grommets and steel sleeves are located on
the upper half of the box and the post grommet in in the
lower half.

5. Carefully remove the protective film from both sides
of the Air Dam.

8. Install the Adapter Coupler and Clamp onto the Fil­ter Adapter.

6. Install the Filter Adapter onto the Air Dam as shown
using the three Button Head Screws and Flat washers.

Connector

Arrow

9. Transfer the Mass Air Flow meter into the Coupler as

shown. Note the location of the connector and direction
indicating arrow. Do not tighten the Clamp at this time.

Grommets and Sleeves

Grommet and Post

10. Transfer the factory air box scoop into the Air Dam

assembly as shown. When properly installed, a distinct
snap will sound indicating that it has locked firmly in
place.

13. Check the positioning of the Mass Air Flow meter in
relation to the wire harness. Readjust if necessary and
tighten the clamps. Reconnect the Air Flow meter.

11. Install the Air Dam assembly into the inner fender
area of the vehicle in the same manner as the OEM air­box. The grommets and sleeves are to be secured to the
inner fender by re using the 6mm nuts that were removed
in step Three.

14. Install the Airaid Premium Filter on to the Filter
Adapter.

12. The bottom of the Air Dam assembly is to be se­cured using the grommet and post. Re connect the in­take tube to the Mass Air Flow meter and reinstall the
battery post cover.

15. Install the Weatherstrip onto the top edge of the Air
Dam with the contour rolling away from the Filter.

Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight. Double check the hood clearance!

Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red

702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household
cleaner and water. Simple
Green®, Formula 409® or equiva­lent works great. Apply cleaner to
outside of air filter and allow to
soak. Then flush filter clean from
the inside out with a garden hose
and repeat steps if necessary. Do
not apply high pressure water or
air to clean filter. Allow filter to
air dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.1.30.14