
Installation Instructions
For Part Numbers:
250-243C 720-242 Airaid Oiled Media Filter
251-243C 721-242 SynthaMax Dry Media Filter - Red
252-243C 722-242 SynthaMax Dry Media Filter - Black
253-243C 723-242 SynthaMax Dry Media Filter - Blue
2010-13 Chevrolet Camaro
6.2L V8
Component Identification
1. Airaid Premium Filter 1
2. Carbon Fiber Intake Tube 1
3. Cold Air Box 1
4. Silicone Hump Hose 1
5. Filter Adapter 1
6. Silicone Reducer 1
7. Weatherstrip 36" 1
8. 3/8" x 18" Breather Hose 1
9. 3/8" Barbed Fitting 1
10. Grommet 1
11. 5/8" Speed Clamp 1
12. Bumper 1
13. Flange Nut 1
14. ¼” Lock Washer 1
15. M6x1.0x12 Hex Bolt 1
16. 1/4” Flat Washer 5
17. ¼-20 x 3/4” Hex Bolt 1
18. ¼” Nylon Lock Nut 1
19. 8-32 x 5/8” Button Head Screw 1
20. #8 Kep Nut 1
21. ¼-20 x 1/2” Button Head Screw 3
22. 8-32 x 3/8” Button Head Screw 2
23. #60 Hose Clamp 1
24. #64 Hose Clamp 2
25. #68 Hose Clamp 1
26. #243 Bracket 1
27. Side Bracket 1
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
Disconnect The Negative Battery Terminal!
1. Remove the oil fill cap. Lift up on the engine cover to
unseat it from the mounts and set it aside .
B.
A.
2. Remove the crankcase breather line:
A.) Sepa rate the br eather line from the air intake
tube.
B.) Locate the locking r ing and its r elease tab inside
of the crankcase breather fitting above the passenger
side valve cover and release it from the steel line. Remove the breather from the vehicle. It will not be reused.
3. Loosen the clamps on the throttlebody and the airbox
and remove the intake tube from the vehicle.
4. Disconnect the Mass Air Flow sensor in the airbox
outlet and remove the two 6mm nuts securing the airbox
assembly to the vehicle.
7. Remove the factory airbox grommets and the steel
inserts inside of them.
5. Lift the complete air box assembly straight up, and
out of the vehicle.
8. Transfer the factory grommets and inserts into the
Cold Air Box.
6. Install the filter adapter (#5) into the Airaid Cold Air
Box, or CAB (#3) as shown using three 1/4-20 Button
Head Bolts (#21), and 1/4” Flat Washers (#16).
9. Turn the CAB upside down and mount the Lower
Bracket (#20) to the bottom using the 1/4-20 x 3/4” Hex
Bolt (#17), 1/4” Flat Washer (#16), and 1/4” Nylock Nut
(#18) as shown. Next- using the 8-32x5/8” Button Head
Screw (#19), and the #8 Kep Nut (#19), attach the plastic
Bumper (#12) to the Bracket as shown.

10. Compress the sides of the factory intake scoop and
remove it from the airbox.
11. Reinstall the factory air scoop into the Airaid Cold
Air Box.
12. Remove and save the ground lug from the driver’s
side inner fender. It will be reused in step #14.
Short Side
Long Side
13. Replace the ground lug from step #12 with the Side
Bracket (#27) as shown using the 6mm x12mm Hex
Bolt (#15), and Lock Washer (#14).
14. Install the Airaid CAB assembly into the vehicle locating the grommets over the factory studs. Reinstall the factory nuts from step #4 onto the studs. Reinstall the factory
ground lug thru the CAB and thru the Side Bracket using
one Flat Washer (#16), and one 6mm Flange Nut (#13).
MAF
Ground Lug
Bracket
Flange Nut
Detailed view of Ground/Bracket assembly
15. Install the Hump Hose (#4) onto the Filter Adapter
using two #64 Hose Clamps (#24). Next install the Reducing Coupler (#6) with one #60 Hose Clamp (#23) on
the throttlebody and one #68 Hose Clamp (#25) on the
open end.
18. Install the 3/8”x18” breather hose between the
Barbed Fitting and the steel crankcase breather tube on
the valve cover. Refer to step #2. Install the Speed
Clamp (#11) over the Breather Hose at the Barbed Fitting as shown.
Barbed Fitting
16. Transfer the Mass Air Flow sensor into the Airaid
Intake Tube (#2) and secure it using two 8-32x3/8” Button Head Screws (#22). Do not attempt to reuse the factory screws. Install the Barbed Fitting (#9) and Grommet
(#10) into the 5/8” hole in the Tube.
19. Install the Airaid Premium Filter (#1) onto the Filter
Adapter and tighten the clamp. Next install the Weather
Strip (#7) onto the top of the CAB. For ease of installation, start the front of the CAB near the radiator and
work your way around towards the fender
17. Install the Airaid Intake Tube (#2) into the Hump
Hose first, and then into the reducing coupler. Adjust
for fit, and tighten all four Hose Camps. It is Very im-
portant to verify that the Intake Tube is not rubbing
on the Radiator or the hood.
20. Reinstall the engine cover and oil fill cap. Double
check your work!
Make sure there is no foreign material in the
intake path. Make sure all clamps, hoses, bolts,
and screws are tight.
Reconnect the negative battery cable!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions
that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are
missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION
IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
720-242 Airaid Oiled Media 721-242 Airaid SynthaMax Dry Media - Red
722-242 Airaid SynthaMax Dry Media - Black 723-242 Airaid SynthaMax Dry Media - Blue
For Your Oiled media filter we suggest using the
AIRAID Filter Tune-Up Kit!
P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
Synthamax Air Filters do not require oil. Service
air filter as needed by cleaning with common nonpetroleum all-purpose household cleaner and water. Simple Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of air filter
and allow to soak. Then flush filter clean from the
inside out with a garden hose and repeat steps if
necessary. Do not apply high pressure water or air
to clean filter. Allow filter to air dry and reinstall.
REV.12.13.13