Airaid 250-230 Installation Instructions

Installation Instructions
For Part Numbers:
250-230 720-475 Airaid Oiled Media Filter 251-230 721-475 SynthaMax Dry Media Filter - Red 252-230 722-475 SynthaMax Dry Media Filter - Black 253-230 723-475 SynthaMax Dry Media Filter - Blue
2008-13 Chevrolet Corvette C6 2010-13 Chevrolet Corvette Grand Sport LS3 6.2L V8
Component Identification
1. Airaid Premium Filter 1
2. Airaid Intake Tube 1
3. Urethane Coupler 1
4. Passenger Side Air Dam 1
5. Driver Side Air Dam 1
6. Weather Strip 9 1/2” 2
7. 8-32 x 3/8” Button Head Screw 4
8. M4 Pan Head Screw 2
9. #8 Flat Washer 4
10. M4 Clip Nut 2
11. Small Rubber Washer 4
12. #64 Hose Clamp 2
13. Grommet 1
14. Grommet 2
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
Clip
1. Disconnect negative battery cable. Remove the grey security clip on the bottom of the Mass Air Flow sensor wiring connector. Next squeeze the tab on the bottom of the connector, and disconnect the wiring harness from the sen­sor. Now loosen the hose clamp holding the tube to the throttle body.
4. Using a #20 Torx Bit, remove the two factory screws that hold the MAF sensor into the factory intake tube. Remove the MAF sensor for reinstal­lation in step #7.
2. Squeeze the tabs on the sides of the crankcase breather connector, and disconnect the breather hose from the factory intake tube breather fitting.
5. Remove the factory breather fitting from the factory intake tube and save it for reinstallation in step #6.
Grommet Post
3. Lift up on the factory intake tube assembly to
disengage the grommets from the three grommet posts and throttle body. Remove the assembly from the vehicle.
6. Install the provided grommet (#13) into the hole in the Airaid Intake Tube (#2). Next install the factory plastic breather fitting removed in step #5 into the grommet.
7. Reinstall the Mass Air Flow sensor removed in step #4, into the Airaid Intake Tube using two 8­32x3/8” button head bolts (#7).
Do Not Use The Factory Screws!
Next, install the urethane coupler (#3) onto the Airaid Intake Tube using two #64 hose clamps (#12) as shown. Tighten only the clamp closest to the MAF sensor.
Driver Side Shown
8. Attach the two air dams (#5 driver side & #4
passenger side) onto the Airaid Intake Tube using one 8-32x1/4” button head bolt (#8) and #8 flat washer (#9) on each side. Leave the bolts slightly loose for now to allow for adjustment.
9. Using a flat blade screwdriver, pry up the cen­ter pin in the grommet post closest to the right fender on the radiator shroud, and remove both pieces of the grommet post from the vehicle.
Grommet Posts
10. Set the Airaid Premium Filter into the area in
front of the radiator. It will be mounted in step #
15.
13. Slide one clip nut (#10) over the outside end of the plastic radiator cover and align it with the hole in the air dam. Install one rubber washer (#11) over the threads of the clip nut, and then align the air dam hole over the washer. Add one more rubber washer, one #8 flat washer (#9), and one M4 Pan Head Screw (#8) to secure the air dam. Repeat this step on the passenger side. Refer to the line drawing on page one.
11. Install the provided grommets (#15), narrow side down, into the Airaid Intake Tube as shown. Make sure that they are seated all the way into the bottom of the holes.
14. Tighten all four button head bolts that secure the air dams to the intake tube, and the radiator shroud.
12. Install the Airaid Intake Tube assembly onto the throttle body first, and then align the grom­mets over the factory grommet posts on top of the radiator shroud. Push down on the grommets to seat them on the posts. (Hint: Use a 1/2” deep socket to help seat the grommets onto the posts.) Now tighten the hose clamp on the throttle body.
15. Slide the Airaid Premium Filter up onto the end of the intake tube and tighten the clamp. Re­connect the MAF sensor wiring harness and re- place the grey security clip. Reconnect the factory breather hose to the breather fitting. Install the weather strip (#6) onto the top of the air dams as shown.
16. Double check your work!
17. Reconnect the negative battery cable!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
720-475 Airaid Oiled Media 721-475 Airaid SynthaMax Dry Media - Red
722-475 Airaid SynthaMax Dry Media - Black 723-475 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter we
suggest using the AIRAID Filter
Tune-Up Kit!
P/N 790-551 Aerosol Spray P/N 790-550 Squeeze Spray
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
Synthamax Air Filters do not require oil. Service air filter as needed by cleaning with common non-petroleum all-purpose household cleaner and wa­ter. Simple Green®, Formula 409® or equivalent works great. Apply cleaner to outside of air filter and allow to soak. Then flush filter clean from the inside out with a garden hose and repeat steps if necessary. Do not apply high pres­sure water or air to clean filter. Allow filter to air dry and reinstall.
REV.12.13.13
Loading...