Airaid 201-711 Installation Instructions

Installation Instructions
For Part Numbers:

200-911 Modular Intake Tube
200-711 Jr. Kit 850-135 Airaid Oiled Media Filter
201-711 Jr. Kit 851-135 SynthaMax Dry Media Filter - Red

2014-15 Chevrolet Silverado 1500/ GMC Sierra
2015 GMC Yukon Denali/XL
2015 Cadillac Escalade/ESV

6.2L V8

Component Identification

1 Airaid Premium Filter 1
2 Airaid Intake Tube 1
3 Hump Hose 1
4 Silicone Coupler 1
5 #60 Hose Clamp 1
6 #64 Hose Clamp 3
7 Speed Clamp 4
8 Barbed Fitting 1
9 Quick Connector 2
10 Barbed Elbow Fitting 1
11 11 1/2" Breather Hose 1
12 23 1/2” Breather Hose 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

B

A

1.Disconnect The Negative Battery Terminal!
A.) loosen the clamps securing the intake system to the

throttle body and the air box.
B.) Disconnect the valve cover breathers from either
side of the factory intake System. Remove the factory
intake system and set it aside.

2. The quick connects for the valve cover breathers are
removed by depressing the grey locking tab in the fit­ting and sliding them off.

3. Install the Barbed Fitting into the Intake Tube as
shown.

4. Install the 90 deg. Barbed fitting into the Intake Tube
exactly as shown.

#64

5. Slide the Hump Hose and #64 Clamps onto the fac-

tory air box. If you are installing an Airaid Jr. kit, in­stall the Airaid Premium Filter at this time.

#60

#64

6. Slide the Coupler with a #60 and #64 clamp onto the

throttle body as shown.

7. Insert the new Quick Connect Fittings into the sup­plied Breather Hoses.

8. Remove the valve cover breathers from both sides of
the motor and set them aside. They will not be reused.

9. Install the Intake Tube and tighten the Clamps. Con­nect the new breathers to the Barbed Fittings in the Intake
tube and the Quick Connect Fittings to the Valve covers .

23 1/2”

11 1/2”

10. The 23 1/2” Hose is to be on the Drivers side. As

shown.

13. Double check your work. Make sure all Clamps are
tight and reconnect the negative battery cable.

11. The 10 1/2” Hose is to be used on the Passenger
side as shown.

WARNING! If your vehicle has a Vehicle Emission Control Information decal affixed to the factory air box and
it is removed, a new replacement label must be obtained and installed in a readily visible position in the engine
compartment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog
check. Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall
not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a
painted surface is recommended.

12. Secure the hose ends with the supplied Speed
Clamps.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not re­quire oil. Service air filter as
needed by cleaning with com­mon non-petroleum all-purpose
household cleaner and water.
Simple Green®, Formula 409®
or equivalent works great. Ap­ply cleaner to outside of air filter
and allow to soak. Then flush
filter clean from the inside out
with a garden hose and repeat
steps if necessary. Do not apply
high pressure water or air to
clean filter. Allow filter to air
dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.09.29.14