Airaid 200-267 Installation Instructions

Installation Instructions

For Part Numbers:

200-267 720-472 Airaid Oiled Media Filter
201-267 721-472 SynthaMax Dry Media Filter - Red
202-267 722-472 SynthaMax Dry Media Filter - Black
203-267 723-472 SynthaMax Dry Media Filter - Blue

2007-08 Chevrolet Silverado 1500/2500/3500

Tahoe/Suburban/Avalanche/
GMC Sierra 1500/2500/3500

Yukon/Yukon XL

Denali/Denali XL

Cadillac Escalade/ESV/EXT

4.8L, 5.3L, 6.0L, 6.2L V-8

*New Body Style GMT-900 Only*

*With Electric Cooling Fans Only*

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Cold Air Box 1

4. Air Filter Adapter 1

5. Urethane Hump Hose 1

6. Urethane Coupler 1

7. 3/8” x 14” Breather Hose 1

8. Weather Strip 25” 1

9. 1/4 - 20 x 1/2” Button Head Bolt 3

10. 1/4” Flat Washer 3

11. #64 Hose Clamp 4

12. 1/4” NPT x 3/8” Barb Fitting 1

13. Edge Clip Cable Tie 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.

Remove the factory engine cover by lifting up on
the front, and then pulling the cover towards the
front of the vehicle. It is only held in place with
grommets.

4. Loosen three hose clamps. One at each end of
the factory intake tube, and one on the Mass Air
Flow sensor (MAF) wher e it clamps to t he fac­tory airbox.

2. Disconnect the factory breather hose at the
valve cover.

5. Slide the factory intake tube off of the MAF
sensor, rotate it up so that it disengages from the
mounting grommet on the intake manifold, and
then slide it forward off of the throttle body and
remove it from the vehicle.

3. Separate the factory intake tube from the plas­tic clamp that secures the radiator hose to the
tube. A firm downward push will usually do it.

6. Remove, and set aside the MAF sensor from
the factory airbox using caution to retain the fac­tory clamp and seal.

7. Rock the factory airbox back and forth to loos­en it from the mounting grommets, and remove it
from the vehicle.

8.Using a 10mm socket, remove four bolts, and
then remove the factory airbox mounting plate
from the vehicle and set aside. Three of these bolts
will be reused in step 11.

9. Install the Filter Adapter (#4) onto the Cold Air
Box, or CAB (#3), as shown using the thr ee 1/4

-20 Button Head Bolts (#9) and 1/4” Washers
(#10).

10. Relocate, and secure the wire harness to the
inner fender edge as shown using the Edge Clip
Cable Tie (#13).

11. Install the Airaid CAB into the vehicle replac­ing the factory airbox. Secure the CAB using the
three of the factory 6mm bolts from step 8. Do
not over tighten.

12. Reinstall the MAF sensor onto the Flter
Adapter, and tighten the clamp.

13. Install the Urethane Hump Hose (#5), and two
#64 Hose Camps (#11) onto the MAF sensor as
shown. Tighten only the clamp on the MAF sen­sor at this time.

13. Install the Airaid Premium Filter (#1) onto the
Air Filter Adapter, and tighten the hose clamp.
Next install the provided Weather Strip (#8) onto
the top of the CAB. For ease of install, start at

the inner fender, and work your way towards the
radiator. Reinstall the engine cover.

14. . Install the 1/4” NPT x 3/8” Barb Fitting
(#12) into the Airaid Intake Tube as shown. Next
install the Urethane Coupler (#6) onto the throttle
body end of the tube using two #64 hose clamps
(#11). Only tighten the Tube side clamp at this
time.

15. Install the Airaid Intake Tube into the Hump
Hose first, and then onto the throttle body. Adjust
for fit, and tighten the hose clamps. Next install
the 3/8” x 14” breather hose (#7) between the
1/4” NPT x 3/8” barbed fitting in the tube, and
the factory port on the valve cover.

16. Double check your work!

Make sure there is no foreign material in
the intake path. Make sure all clamps, hos­es, bolts, and screws are tight.

WARNING! If your vehicle has a Vehicle E mission Contr ol In for mation decal a ffixed to the factor y air ­box, a new replacement label must be obtained and installed in a readily visible position in the engine compart­ment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check.
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall not be
affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a paint­ed surface is recommended.

17. Reconnect the negative bat­tery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILiTY! The air filter is
reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red

722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.10.14.13