Airaid 200-233 Installation Instructions

Installation Instructions

For Part Numbers:

200-233 720-472 Airaid Oiled Media Filter
201-233 721-472 SynthaMax Dry Media Filter - Red
202-233 722-472 SynthaMax Dry Media Filter - Black
203-233 723-472 SynthaMax Dry Media Filter - Blue

2009-13 Chevrolet Silverado 1500

Tahoe/Suburban 1500/Avalanche 1500/

GMC Sierra 1500/

Yukon/Yukon XL/Denali/Denali XL

2009-14 Cadillac Escalade/ESV/EXT

4.8L V8, 5.3L V8, 6.0L V8*, 6.2L V8
*With Electric Cooling Fans Only*

*Does not fit 6.0L motors after 2010

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Rear Air Dam Panel 1

4. Airaid Intake Tube 1

5. Air Filter Adapter 1

6. Urethane Hump Hose 1

7. Urethane Coupler 1

8. 3/8” x 14” Breather Hose 1

9. Weather Strip 20 3/4” 1

10. 6-32 x 5/16” Screw 5

11. #6 Flat Washer 5

12. 6-32 Keps Nut 5

13. 8-32 x 5/8” Button Head Bolt 2

14. 1/4 - 20 x 1/2” Button Head Bolt 3

15. 1/4” Flat Washer 7

16. M6 - 1 x 25 Hex Bolt 4

17. #64 Hose Clamp 4

18. 1/4” NPT x 3/8” Barb Fitting 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.

Remove the factory beauty cover by lifting up on
the front, and then pulling the cover towards the
front of the vehicle. It is only held in place by
grommets.

2. Disconnect the factory breather hose at the
valve cover by pulling the small black tab on the
fitting towards the front of the vehicle, and then
to the right.

3. Separate the factory intake tube from the plas­tic clamp that secures the radiator hose to the
tube. A firm downward push will usually do it.

4. Loosen two hose clamps on the factory intake
tube. One at the throttlebody, and one where it
clamps to the factory airbox. Remove the factory
intake tube from the vehicle.

7. Using a 10mm socket, remove four bolts, and
then remove the factory airbox mounting plate
from the vehicle.

5. Remove, and set aside the MAF (Mass Air
Flow) sensor from the factory airbox. This will

require a T15 Torx Bit.

8. Assemble the Cool Air Dam panels (CAD) (#2
& #3) using five 6-32 x 5/16” screws (#10), #6
flat washers (#11), and 6-32 keps nuts (#12). Next
install the air filter adapter (#5) into the panels as
shown with the hole for the Mass Air Flow sen­sor facing up, using three 1/4 - 20 x 1/2” button
head bolts (#14), and 1/4” flat washers (#15).

6. Rock the factory airbox back and forth to loos­en it from the mounting grommets, and remove it
from the vehicle.

9. Install the Airaid CAD assembly into the vehi-
cle replacing the factory airbox. Secure the CAD
using four M6 x 1.25 Hex Bolt (#16), and 1/4”
flat washers (#15). Do not over tighten the four
bolts.

10. Reinstall the MAF sensor onto the filter
adapter using two 8-32 x 5/8” Allen Bolts (#13).

Do Not Use The Factory Screws!

Next install the urethane hump hose (#6) onto the
MAF with the two #64 hose clamps (#17). Leave
the clamps loose for now.

13. Install the Airaid Premium Filter (#1) onto the
air filter adapter, and tighten the hose clamp. Next
install the provided weather strip (#9) onto the top
of the CAD. For ease of install, start at the inner

fender, and work your way towards the radiator.

Reinstall the beauty cover.

11. Install the 1/4” NPT x 3/8” Barb Fitting (#18)
into the Airaid Intake Tube as shown. Next install
the urethane coupler (#7) onto the throttle body
end of the tube using two #64 hose clamps (#17).
Tighten only the clamp on the tube.

12. Install the Airaid Intake Tube into the hump
hose first, and then onto the throttle body. Adjust
it for fit, and tighten the hose clamps. Next install
the 3/8” x 14” breather hose (#8) between the
1/4” NPT x 3/8” barbed fitting in the tube, and
the factory port on the valve cover.

14. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts,
and screws are tight.

15. Reconnect the negative battery cable!

WARNING! If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a

new replacement label must be obtained and installed in a readily visible position in the engine compartment in
order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replace­ment labels can be ordered from your local dealership. Regulations state that the VECI label shall not be affixed
to any equipment which is easily detached from the vehicle. Label placement, under the hood on a painted sur­face is recommended.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is
reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red

722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.04.11.14