Airaid 200-196 Installation Instructions

Installation Instructions
For Part Numbers:
200-196 700-469 Airaid Oiled Media Filter 201-196 701-469 SynthaMax Dry Media Filter - Red 202-196 702-469 SynthaMax Dry Media Filter - Black 203-196 703-469 SynthaMax Dry Media Filter - Blue
2007-08 Cadillac Escalade/ESV/EXT 2007-08 Chevrolet Avalanche 2007-08 Chevrolet Silverado 1500/2500HD/3500HD 2007-08 Chevrolet Tahoe/Suburban 1500/2500 2007-08 GMC Sierra 1500/2500HD/3500HD 2007-08 GMC Yukon/Yukon XL 1500/2500 2007-08 GMC Denali/Denali XL
4.3L V6, 4.8L V8, 5.3L V8, 6.0L V8, 6.2L V8 (GMT-900 Body Style Only)
Component Identification
1. Airaid Premium Filter 1
2. MAF Panel Coated 1
3. Rear Air Dam Coated 1
4. Black Filter Adapter 1
5. Weather Strip 20 3/4” 1
6. 1/4”-20x1/2” SS Button Head 3
7. 1/4” Flat Washer 7
8. M6 x 1.25 Hex Bolt 4
9. 6-32 x 5/16” Screw 5
10. #6 Flat Washer 5
11. 6-32 Keps Nut 5
Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.
1. Disconnect the negative battery cable. Loosen the hose clamp on the end of the factory intake tube at the Mass Air Flow sensor, next loosen the hose clamp that holds the Mass Air Flow sensor to the factory air box.
2. Remove the Mass Air Flow sensor from be­tween the factory intake tube and the factory air box. Use caution to retain the rubber coupler on the Mass Air Flow sensor.
3. Without disconnecting the wiring harness, set the Mass Air Flow sensor out of the work area. Next rock the factory air box back and forth, lift it up, and remove it from the hold down grommets. There are no bolts holding it down.
4. Remove the factory air box from the vehicle. 5. Remove 4 bolts, and remove the factory air­box mounting plate.
7. . Install the filter adapter (#4) into the CAD
using three button head bolts (#6), and washers (#7).
8. Install the assembled CAD in place of the fac- tory airbox using four bolts (#8) and washers (#7). Do not over tighten the bolts.
6. Assemble the two Cool Air Dam panels (#2) and (#3) using the five supplied screws (#9), washers (#10), and nuts (#11), as shown.
9. Re-install the Mass Air Flow sensor and cou- pler onto the air filter adapter (#4), as shown and tighten the hose clamp. Next re-connect the fac­tory intake tube to the Mass Air Flow sensor, and tighten the hose clamp.
11. Double check your work!
Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.
10. Install the Airaid Premium Filter (#1) onto the
filter adapter (#4), and tighten the hose clamp. Next install the weather strip (#5) onto the top of the CAD as shown. For ease of installation start at the fender, and work towards the radiator.
WARNING! If your vehicle has a Vehicle Emission Contr ol Infor mation decal affixed to the factor y airbox, a new r eplacement label must be obtained and installed in a readily visible position in the engine compartment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall not be affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a painted surface is recommended.
12. Reconnect the negative battery cable!
Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.
FILTER IDENTIFICATION
700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red 702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue
For your Oiled media filter
we suggest using the AIRAID
Filter Tune-Up Kit!
P/N 790-551 Aerosol Spray P/N 790-550 Squeeze Spray
Synthamax Air Filters do not re­quire oil. Service air filter as need­ed by cleaning with common non­petroleum all-purpose household cleaner and water. Simple Green®, Formula 409® or equivalent works great. Apply cleaner to outside of air filter and allow to soak. Then flush filter clean from the inside out with a garden hose and repeat steps if necessary. Do not apply high pressure water or air to clean filter. Allow filter to air dry and reinstall.
Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 (800) 498-6951 AiraidInfo@airaid.com www.airaid.com
REV.11.14.13
Loading...