Airaid 200-187 Installation Instructions

Installation Instructions

For Part Numbers:

200-187 700-469 Airaid Oiled Media Filter
201-187 701-469 SynthaMax Dry Media Filter - Red
202-187 702-469 SynthaMax Dry Media Filter - Black
203-187 703-469 SynthaMax Dry Media Filter - Blue

2006 Chevrolet Silverado 2500HD/3500HD
2007 Chevrolet Silverado “Classic” 2500HD/3500HD

6.6L V8 Duramax Diesel “LLY” or “LBZ”
With High Profile Hood

Note: For GMC Trucks with Low Profile Hood
Use Part # 200-189

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Rear Panel 1

4. MAF Adapter Tube 1

5. Weather Strip 20 3/4” 1

6. 1/4”-20x1/2” Button Head 3

7. 1/4” Flat Washer 7

8. 8-32x1/2” Button Head Screw 2

9. M6-1x25 Hex Bolt 4

10. 6-32x 5/16” Screw 5

11. #6 Flat Washer 5

12. 6-32 Keps Nut 5

13. Rubber Trim 6 1/2” 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

1. Disconnect the negative battery cable.
Using a 5/16” socket or flat screwdriver, loosen
the hose clamp that holds the factory airbox to the
flexible intake tube.

2. Using a #20 Torx bit, remove 2 screws hold­ing the Mass Air Flow sensor to the factory air-
box tube.

3. Without disconnecting the wiring harness,
remove the Mass Air Flow sensor from the fac-
tory airbox, and set it aside.

4. Slide the flexible intake tube off of the factory
airbox and then rock the airbox back and forth to
free it from the mounting grommets, next lift it
straight up and remove it from the vehicle.

7. Assemble the two Cool Air Dam (CAD) panels
(#2) and (#3) as shown, using the five 6-32 screws
(#10), washers (#11), and nuts (#12).

5. Remove the factory filter minder and grommet
from the factory airbox. Save them for later use.

8. Install the Airaid intake tube (#4) into the Cool
Air Da m using th e thr ee 1/4”-20x1/2” button

head bolts (#6), and washers (#7) as shown.

6. Using a 10mm socket, remove 5 bolts from the
factory airbox mounting plate. Remove the plate
from the vehicle.

9. Re-install the factory grommet and filter
minder removed in step #5 into the Airaid intake
tube.

10. Install the provided rubber trim (#13) on the
CAD as shown.

13. Install the Airaid Premium Filter (#1) onto

the Airaid intake tube (#4), and tighten the hose
clamp. Now install the provided weather strip
(#5) on the top of the CAD. For ease of installa­tion, start near the fender and work your way
towards the radiator.

11. Install the assembled CAD into the vehicle
where you removed the factory mounting plate
in step #6. Use four bolts (#9), and washers (#7)
to secure the CAD. Do not over tighten the bolts.

12. Re-position the factory intake tube onto the
Airaid tube, and tighten the hose clamp. Next re­install the Mass Air Flow sensor into the Airaid
tube using the two provided Button Head screws
(#8). Do not use the factory screws! Do not
over tighten!

14. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws
are tight.

15. Reconnect the negative battery cable!

WARNING! If your vehicle ha s a Vehicle Emission Con tr ol Infor mat ion decal affixed to the factor y air box,

a new replacement label must be obtained and installed in a readily visible position in the engine compartment in
order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replace­ment labels can be ordered from your local dealership. Regulations state that the VECI label shall not be affixed to
any equipment which is easily detached from the vehicle. Label placement, under the hood on a painted surface is
recommended.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red

702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.14.13