Airaid 200-183 Installation Instructions

Installation Instructions

For Part Numbers:

200-183 700-469 Airaid Oiled Media Filter
201-183 701-469 SynthaMax Dry Media Filter - Red
202-183 702-469 SynthaMax Dry Media Filter - Black
203-183 703-469 SynthaMax Dry Media Filter - Blue

2003-09 Hummer H2/H2 SUT

6.0L V8, 6.2L V8

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel Coated 1

3. Bottom Panel Coated 1

4. Filter Adapter 1

5. Weather Strip 24 ¾” 1

6. ¼ -20 x 5/8” Bolt 3

7. ¼” Flat Washer 3

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

A.

B.

1.Disconnect the negative battery cable.
A.) Disconnect the Mass Air Flow (MAF) sensor
wiring harness.
B.) Loosen the two hose clamps on the MAF sen­sor and remove it.

2. Using a 10mm socket, remove the three bolts
that secure the factory airbox to the inner fender
(save for reuse).

3. Remove the factory airbox and set it aside.
Using a flat blade screwdriver, remove and save
the three factory rubber grommets and inserts
from the airbox base.

4. Assemble the Airaid Cool Air Dam panels (#2,
#3) using the factory rubber grommets and inserts
as shown.

7. Slide the MAF sensor onto the filter adapter and
tighten the clamp. Slide the factory intake tube
onto the other side of the MAF sensor, and tighten
the clamp. Reconnect the MAF sensor wiring har-
ness.

5. Install the filter adapter (#4) into the Airaid Cool
Air Dam using three 1/4-20x 5/8” bolts (#6), and 1/4”
flat washers (#7).

8. Install the Airaid Premium Filter (#1) onto
the filter adapter, and tighten the hose clamp.
Install the provided weather strip (#5) onto
the top edge of the panel. (Hint: Start at one

end, and work to the other.)

Reuse 3 factory
bolts.

6. Install the Airaid Cool Air Dam over the three
factory mounting points, and fasten with the
factory bolts saved in step #2.

9. Congratulations on installing your new in­take system! See the back of this page for fur­ther instructions.

10. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight.

11. Reconnect the negative battery cable!

WARNING! If your vehicle has a Vehicle Emission Control Infor mation decal affixed to the factor y air box, a new re-

placement label must be obtained and installed in a readily visible position in the engine compartment in order to remain
CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replacement labels can be ordered
from your local dealership. Regulations state that the VECI label shall not be affixed to any equipment which is easily de­tached from the vehicle. Label placement, under the hood on a painted surface is recommended.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST week­days for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and
packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air
filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WA­TER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red

702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Synthamax Air Filters do not re­quire oil. Service air filter as need-

ed by cleaning with common non-

petroleum all-purpose household
cleaner and water. Simple Green®,
Formula 409® or equivalent works
great. Apply cleaner to outside of
air filter and allow to soak. Then
flush filter clean from the inside out
with a garden hose and repeat steps
if necessary. Do not apply high
pressure water or air to clean filter.
Allow filter to air dry and reinstall.

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.14.13