Airaid 200-129 User Manual

Installation Instructions

For Part Numbers:

200-129 700-469 Airaid Oiled Media Filter
201-129 701-469 SynthaMax Dry Media Filter - Red
202-129 702-469 SynthaMax Dry Media Filter - Black
203-129 703-469 SynthaMax Dry Media Filter - Blue

2001-04 Chevrolet Silverado 2500HD/3500HD
2001-04 GMC Sierra 2500HD/3500HD

6.6L V8 Duramax Diesel “LB7”
(Will NOT fit the 2004 “LLY” Engine)

Component Identification

1. Airaid Premium Filter 1

2. MAF Panel 1

3. Rear Air Dam 1

4. Filter Adapter 1

5. Airaid Intake Tube 1

6. Urethane Hump Hose 1

7. Urethane Coupler 1

8. Weather Strip 19 ½” 1

9. 6-32 x 5/16” Screw 5

10. #6 Flat Washer 5

11. 6-32 Keps Nut 5

12. ¼ - 20 x 5/8” Hex Bolt 3

13. ¼” Flat Washer 7

14. M6-1x 25 Hex Bolt 4

15. 8-32 x ½” Button Head 2

16. Steel Washer 2

17. #72 Hose Clamp 2

18. #60 Hose Clamp 2

19. T20 Security Bit 1

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

A.

B.

1. Disconnect the negative battery cable.
A.) Disconnect the Ma ss Air Flow (M.A.F.)

sensor wiring harness. Using the supplied T-20
Security bit, remove the two screws and the
M.A.F. sensor fr om t he tube (save the sensor
for reuse).
B.) Loosen t he hose clamps on ea ch end of the
factory intake tube assembly.

2. Remove the factory filter minder and grommet
from the side of the factory airbox (save for re­use).

3. Remove the factory intake tube assembly from
the engine. Rock the factory air box back and
forth and remove it from the vehicle. There are
only grommets holding it in, no bolts.

4. Using a 10mm socket, remove the five bolts
and mounting plate from the engine compartment.

7. Install the Airaid Cool Air Dam assembly in
the engine compartment using four M6-1x25 hex
bolts (#14) and 1/4” flat washers (#13).

5. Assemble the Airaid Cool Air Dam panels (#2,
#3) using five 6-32 x 5/16” screws (#9), #6 flat
washers (#10) and 6/32 keps nuts (#11).

8. Place two steel washers (#16) into the recessed
portions of the MAF sensor mounting holes.

6. Using three ¼-20 x 5/8” hex bolts (#12) and
1/4” flat washers (#13), install the filter adapter
(#4) onto the Airaid Cool Air Dam.

9. Using two 8-32 x 1/2” button head screws
(#15) install the factory M.A.F. sensor in the
Airaid intake tube (#5) DO NOT USE THE FAC-

TORY SCREWS! (Note: Sensor must be in­stalled in the direction shown in the picture, with
steel washers between it and the tube.)

10. Install the factory rubber grommet and air
filter minder into the Airaid intake tube.

B.

A.

11. Install the urethane hump hose (#6) and two

#72 hose clamps (#17) onto the large end of the
Airaid intake tube. (Note: Leave hose clamps

loose until final assembly.)

12. Install the urethane coupler (#7) and two #60
hose clamps (#18) onto the small end of the
Airaid intake tube. (Note: Leave hose clamps

loose until final assembly.)

15. Double check your work!

Make sure there is no foreign material in
the intake path. Make sure all clamps,
hoses, bolts, and screws are tight.

16. Reconnect the negative bat­tery cable!

13. A.) Inst all the hump hose end of the Air aid

intake tube assembly onto the filter adapter first.
B.) Slip the coupler end of the tube over th e
factory turbocharger inlet. Adjust for fit, and
tighten the hose clamps. (Note: There should be a

gap in between the Airaid intake tube and the air
filter adapter.)

WARNING! If your vehicle has a Veh icle E mission Contr ol Infor mation decal affixed to the factor y air ­box, a new replacement label must be obtained and installed in a readily visible position in the engine compart­ment in order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check.
Replacement labels can be ordered from your local dealership. Regulations state that the VECI label shall not be
affixed to any equipment which is easily detached from the vehicle. Label placement, under the hood on a paint­ed surface is recommended.

14. Install the Airaid Premium Filter (#1) onto
the filter adapter, and tighten the hose clamp.
Install the weather strip (#8) onto the Airaid Cool
Air Dam. Reconnect the M.A.F. sensor wiring
harness. (Note: Start from one corner and work

your way around to insure proper alignment of
the weather strip.)

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

700-469 Airaid Oiled Media 701-469 Airaid SynthaMax Dry Media - Red

702-469 Airaid SynthaMax Dry Media - Black 703-469 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we

suggest using the AIRAID Filter

Tune-Up Kit!

P/N 790-551 Aerosol Spray

FILTER IDENTIFICATION

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning
with common non-petroleum all-purpose
household cleaner and water. Simple
Green®, Formula 409® or equivalent
works great. Apply cleaner to outside of
air filter and allow to soak. Then flush
filter clean from the inside out with a gar­den hose and repeat steps if necessary.
Do not apply high pressure water or air
to clean filter. Allow filter to air dry and
reinstall.

P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

REV.11.12.13