Airaid 200-111 Installation Instructions

Installation Instructions

For Part Numbers:

200-111 720-472 Airaid Oiled Media Filter
201-111 721-472 SynthaMax Dry Media Filter - Red
202-111 722-472 SynthaMax Dry Media Filter - Black
203-111 723-472 SynthaMax Dry Media Filter - Blue

2014-15 Chevrolet Silverado & GMC Sierra
2015 Cadillac Escalade
2015 GMC Yukon Denali & Denali XL

6.2L V8

Component Identification

1. Airaid Premium Filter 1

2. Airaid Intake Tube 1

3. Cold Air Box 1

4. Filter Adapter 1

5. Silicone Hump Hose 1

6. Silicone Reducing Coupler 1

7. 5/8" x 12” Breather Hose 1

8. 5/8" x 9.5" Breather Hose 1

9. Weather Strip 25 ½” 1

10. #68 Hose Clamp 2

11. #60 Hose Clamp 1

12. #56 Hose Clamp 1

13. #19 Speed Clamp 4

14. 3/8" NPT x 5/8" Barb Elbow 1

15. 3/8" NPT x 5/8" Barb Fitting 1

16. ¼-20 x 1/2” Button Head Cap Screw 3

17. #8-32 x ½” Button Head Cap Screw 2

18. SAE 90 Deg. Quick Connect Fitting 2

19. 1/4” Flat Washer 3

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

A

B

1.Disconnect The Negative Battery Terminal!
A. Depress the Grey locking tabs in the PCV breather

quick connect fittings and remove them from the vehi­cle.
B. Loosen the clamps on the factory intake assembly
and remove it from the vehicle.

Fender Brace

MAF

2. Using an open end wrench, remove the passenger

side fender brace and set it aside. Unplug the Mass Air
Flow sensor, or MAF and un anchor it from the airbox.
Unseat the airbox from it’s mounting grommets and
remove the factory airbox.

3. . Remove the 4 bolts in the airbox mounting tray and
set them aside. They will be reused in step 5. Remove the
Tray, it will not be re used.

Elbow

4. Install the Filter Adapter onto the Cold Air Box as

shown using the three 1/4-20 Button Head Screws (#16)
and 1/4” Flat Washers (#19).

7. Transfer the Mass Air Flow sensor from the factory
airbox into the Airaid Intake Tube. Secure the sensor
using the two 8-32 Button Head Screws (#17).

Do Not Use Factory Hardware !

5. Slide the Airbox assembly into the inner fender area

and secure it using 3 of the OEM bolts removed in step

3.

#60 Clamp

#56 Clamp

#68 Clamps

8. Slide the Hump Hose with the #68 Hose Clamps

onto the Filter Adapter and the Reducing Coupler with
the #60 and #56 Clamps onto the throttle body. Leave
the clamps loose for now.

Fitting

6. Install the Barbed Fitting and Elbow (#s 13 and 14)

into the Airaid Intake Tube as shown.

9. Install the Airaid Intake Tube into the Hump Hose and
couplers. Adjust for fit and tighten all four Hose Clamps.

9 1/2” Hose

12” Hose

10. Install the supplied Quick Connect Fittings on to the

valve cover breather fittings.

13. Install the Airaid Premium filter onto the Filter
Adapter , and tighten the hose clamp.

11. Connect the Barbed Fittings on the Intake tube to the
Quick Connect Fittings on the Valve covers using the 5/8
Breather hoses. The 9 1/2” Hose is to be used on the Pas­senger side and the 12” Hose is to be on the Drivers side.

14. . Install the Weather Strip onto the top edge of the
Cold Air Box with the contour rolling away from the
filter.

12. Reconnect the Mass Air Flow sensor.

15. Reinstall the fender brace. Make sure all clamps,

hoses, bolts, and screws are tight. Double check the
hood clearance. Reconnect the negative battery cable.

WARNING! If your vehicle has a Vehicle Emission Control Information decal affixed to the factory airbox, a
new replacement label must be obtained and installed in a readily visible position in the engine compartment in
order to remain CARB compliant. Failure to do so will prevent the vehicle from passing a smog check. Replace­ment labels can be ordered from your local dealership. Regulations state that the VECI label shall not be affixed to
any equipment which is easily detached from the vehicle. Label placement, under the hood on a painted surface is
recommended.

Thank you for purchasing the Airaid Intake System. Contact Airaid @ [phone] 8:00 AM - 5:00 PM MST weekdays for questions
regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are
missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to wa­ter and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILITY! The air filter
is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

720-472 Airaid Oiled Media 721-472 Airaid SynthaMax Dry Media - Red

722-472 Airaid SynthaMax Dry Media - Black 723-472 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter

we suggest using the AIRAID

Filter Tune-Up Kit!

P/N 790-551 Aerosol Spray
P/N 790-550 Squeeze Spray

Airaid Filter Co. 2688 E Rose Garden Ln. Phoenix AZ 85050 [phone] [e-mail] www.airaid.com

Synthamax Air Filters do not require oil.
Service air filter as needed by cleaning with
common non-petroleum all-purpose house­hold cleaner and water. Simple Green®,
Formula 409® or equivalent works great.
Apply cleaner to outside of air filter and
allow to soak. Then flush filter clean from
the inside out with a garden hose and re­peat steps if necessary. Do not apply high
pressure water or air to clean filter. Allow
filter to air dry and reinstall.

REV.01.26.15