Aiphone NE-SSV User Manual

0607

Vandal Resistant Sub Station with built in Color Pinhole Camera for use with

NEM, NDR, NDRM Systems

- INSTRUCTIONS -

The NE-SSV is a 2-gang vandal and weather resistant sub station designed for use with the NEM, NDR and NDRM
systems. It is constructed of 12 gauge stainless steel and has a stand alone color camera built in. It is also equipped with
an option for an external output contact closure when the sub station places a call (relay required). The unit either flush
mounts into a 2-gang box, or surface mounts using the SBX-2G. Each unit includes a 12V DC power transformer for the
camera, tamper proof screws, and a tool for installation.

INSTALLATION:

1. For flush mounting, install sub station in standard 2-gang electrical box with minimum 2-1/2" depth.

2. For surface mounting, use the SBX-2G surface mount enclosure (sold separately).

3. Only the 12V DC power transformer included should be used to power the NE-SSV camera.

5. IMPORTANT! These units are designed for use in normal weather conditions, and to allow drainage and
evaporation of moisture that naturally gets into the unit. Do not apply caulking or silicone sealant around the

unit when installing, and do not use weather stripping around the perimeter of the box when mounting. If

sealing the unit is required, the bottom must remain unsealed. Sealing the unit will prevent or inhibit moisture from
dissipating from inside the unit, which may cause corrosion or deterioration of the internal components over time.

Speaker

50cm

20”

Front View Back View

Camera

Call button

45cm

18”

50cm / 20”

67cm
26½”

The view achieved if the subject is 20" from the
camera is: 18" Vertically and 26½” Horizontally

Transparent corner shadowing
on the picture is normal.

Page 1

WIRING DIAGRAMS:

NEM/NDR

Master

1
2
3
~

20

PS-2420UL

+

-

E
+

-

H

Dry closure

output for

duration of call-in

12V DC power input for camera

(Red - Must use supplied transformer)

Video output to monitor

or CCTV system (Yellow)

Blk Blk

RY-PA

Yel

12VDC power in (Red)

NE-SSV

(w/dry closure output)

Red

Blk
Blu

Pur

NE-SSV

(w/corridor lamp)

Red

Blk
Blu

Blu
Blu

NBY-4A

NE-SSV

Red

Blk

Pur

Blu

+

-

PS-2420UL

12VDC power in

(Red)

Video Out (Yellow)

NDRM Master

CP-544A board

1
E

H

2
E
H

CP-544A board

A+

A-

B+

B-

H
Q
E
S
B
Y

A1
V1
A2
V2

Video Out (Yellow)

Dry closure

output for

duration of

call-in

12VDC power in (Red)

Video Out (Yellow)

Blk

RY-PA

Yel

Blk

NE-SSV

(w/dry closure output)

Red

Blk

Pur

Blu

Page 2

NE-SSV BACK VIEW:

Color Camera

Call Button

Red connector for 12V DC camera
power input (from included power supply)
Power supply dimensions:
1-⅝" W x 2-¼” H x 1-⅝” D
6' DC cord.

Speaker

NOTE: If using fiber optic interface, the video input on

Red: # terminal of Master
Blue: Corridor Lamp (optional)

the IFS VIC-5211 is not compatible with the NE-SSV
camera. The VIC-5211 can be used for audio only,
with a separate fiber module required for video.

Black: E of Master
Purple: Relay for call-in closure (optional)

Yellow BNC connector for
video output

SPECIFICATIONS:

Audio Power Source: Supplied by master station
Speaker: 20 ohms, 4W, 2" diameter, water proof and puncture resistant, 2.4 oz. magnet
Call Button: SPST call button, momentary activation. Limited stop button.
Call Annunciation: Pressing the call button at sub activates and latches call at NEM/NDR/NDRM master. The master

station's LED will be lit and a ringing tone will be heard until the call is answered.
Communication: Hands free at sub. Master is push-to-talk or VOX with handset.
CCTV Camera Output: 75 Ohm, 1Vp-p, NTSC, DC-coupled
Iris Control: Auto
Minimum Illumination: 1.0 lux
Camera image sensor: 1/3" CCD
Focal Length: 4.3mm Cone Pinhole Lens (78°)
Effective Pixels: 510(H) x 492(V) NTSC
Camera Power Source: 12V DC, 100mA (via included power supply)
MTBF: (Mean Time Before Failure) 80,000 Hours
Faceplate: 12 gauge stainless steel
Mounting: Flush mount into a 2-gang box (minimum 2-½” depth) or surface mount into SBX-2G (sold separately)

Tamper proof screws included (6x32 for use with flush 2-gang box) with T-10 TORX bit

When using SBX-2G, use the hardware included with that unit.
Terminations: Color-coded prewired pigtails
Operating Temperature: 14
Audio Wiring: 2 conductors homerun; or 1 common plus 1 individual per sub, looped through each sub.

Audio Wiring Distance: 420' with 22AWG; 1,000' with 18AWG
Video Wiring: Independent BNC connection from substation pigtail to destination video device
Dimensions (HxWxD): NE-SSV alone: 4-11/16" x 4-11/16" x 2"

F ~ 140°F (-10°C ~ 60°C)

Shielded cable is recommended.

Use Aiphone #822202 or #821802 for homerun wiring, #822206 for up to 5 stations

on each run, or #822210 for up to 9 stations on each run.

With SBX-2G: 4-3/4" x 4-7/8" x 3-5/8" (Top) 2-3/8" (Bottom)

Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
[phone]
FAX [phone]

TOLL FREE TECHNICAL SUPPORT: [phone]

TOLL FREE FAX LINE: [phone]

TECHNICAL SUPPORT E-MAIL: [e-mail]

NE-SSV Instr.

0607JDJS