Aiphone MYW-MD INSTALLATION INSTRUCTIONS

Page 1
Special Order Products
MYW-MD
Video Modulator/Demodulator for MY series Video Systems
- INSTRUCTIONS -
The MYW-MD adaptor converts the video from a 2-wire signal to a standard coaxial video signal (Demodulator mode). It can also be used to convert a standard CCTV camera's signal to a 2-wire signal, compatible with Aiphone's MY series video monitors (Modulator mode).
MODULATOR
MYW-MD to integrate a Standard CCTV camera with an Aiphone Monitor
MY-DC
A1 A2
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
JUMPER CLIP: (Located under rubber cover in upper right corner of the faceplate of the MYW-MD) Set in Modulator (top) position from factory.
Ensure that jumper clip is between the top two pins.
Center cond. to MV+
Braid to MV-
MYW-MD
MA1 MA2
MV+
MV-
+
-
Polarized
PS-18C
MY-2CD*
1A1 1A2
2A1 2A2
*MYW-MD Can also be used with: MY-1CD MY-CU MYW-P1L MYW-P3L (input only)
B1 B2
+
-
+
-
MYW-MD TERMINAL DEFINITIONS:
MODULATOR: MA1 2-Wire output to MA2 MY monitor/adaptor
MV+ Coax input: center cond. MV- Coax input: Braided shield
+ Positive 18V DC
- Negative Input signal requirements:
75 ohm, 1V peak-to-peak. Coax: Solid copper core with copper braid.
DEMODULATOR: DA1 2-Wire input from DA2 MY monitor/adaptor
DV+ Coax output: center cond. DV- Coax output: Braided shield
+ Positive 18V DC
- Negative Output signal:
75 ohm, 1V peak-to-peak. Coax: Solid copper core with copper braid.
Pg. 1
Page 2
MODULATOR
Pg. 2
Master Sentry Intercom and Video System with Standard CCTV Cameras
MY-DC
A1 A2
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
Center cond. to MV+
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
Center cond. to MV+
Braid to MV-
Braid to MV-
MYW-MD
MA1 MA2
MV+
MV-
+
-
MYW-MD
MA1 MA2
MV+
MV-
Polarized
LE-DA*
1 E
-
* Any LE or LS series door station may be used.
Polarized
MYW-P3L
1A1 1A2
2A1 2A2
DA DB
E R
12+
12-
EL2
KA KB
18+
18-
3A1 3A2
B1 B2 U1 U2
LEF-10C*
10
9 E
R
12+
12-
L
K10
K9
* Any 5 or 10 call LEF series master can be used.
Separate video cable from intercom cable
MYH-CUB*
A1 A2 U1 U2
+
-
JUMPER CLIP: (Located under rubber cover in upper right corner of the faceplate of the MYW-MD) Set in Modulator (top) position from factory.
Ensure that jumper clip is between the top two pins.
System Configurations:
1 Aiphone video door station and 2 CCTV cameras
or
2 Aiphone video door stations and 1 CCTV camera
Optional:
Part #261380 - Video Output connector for MYW-P3L. (Provides a 1V peak-to-peak video signal output.)
PS-18C
18+
18-
NOTES:
1. In the above system example, the CCTV cameras are addressed by pressing the MONITOR button on the MYH-CUB. Press once to turn on camera 1 (MY-DC), press again to switch to camera 2 (CCTV #1), pressing MONITOR a third time will switch to Camera 3 (CCTV #2) and a fourth time turns the monitor off.
2. The LE-DA will become active by selecting station #9 on the LEF-10C. Selecting this station will also activate CCTV camera #2. The camera will not activate when the LE-DA calls in.
ONLY WIRING RELATING TO THIS APPLICATION IS SHOWN HERE. SEE PRODUCT INSTRUCTIONS FOR COMPLETE WIRING INFORMATION.
+
-
* Use MYH-CU for surface mount applications.
+
-
Page 3
DEMODULATOR
Pg. 3
MYW-MD used for VIDEO OUTPUT with Aiphone MY series Video Entry Systems
The picture from the Video Door Station can be seen at standard monitors whenever the Aiphone system is activated.
MY-DC
A1 A2
MY-1CD
1A1 1A2
Polarized
MYW-MD*
DA1 DA2
DV+
DV-
Center cond. to DV+
Braid to DV-
Coax output to standard video input. (CCTV monitor, RF modulator, or into cable distribution network through a multiplexer.)
PS-18YC/A
* Used for video OUTPUT with
Red
Blk
+
-
+
-
MY-1CD, MY-CU, MYW­P3CB MYW-P1L, and MYW­P3L.
JUMPER CLIP: (Located under rubber cover in upper right corner of the faceplate of the MYW-MD) Move to Demodulator (lower) position.
Ensure that jumper clip is between the bottom two pins.
DEMODULATOR
MY Video Door Station with Standard Monitor (No audio communication or PanTilt capabilities)
MYW-MD*
DA1 DA2
DV+
DV-
To standard monitor or monitor input on a
video switcher.
Center cond. to DV+
Braid to DV-
Standard 9"
Monitor
*Any MY series camera can be used
MY-DC*
A1 A2
IMPORTANT:
CN2 speaker microphone connector inside Aiphone Video door station must be unplugged to prevent the possibility of feedback.
JUMPER CLIP: (Located under rubber cover in upper right corner of the faceplate of the MYW-MD). Move to Demodulator (lower) position.
Ensure that jumper clip is between the bottom two pins.
TO POWER THE CAMERA: (1) WHEN IN USE
- Install a switch or relay contact in series with the "+" terminal from the power supply (see diagram.)
- Solder a jumper between points labeled AA on the MYW-MD main PC board. (see Illustration) This allows the camera to be activated manually, or when the relay contact is activated from a separate source.
(2) CONTINUALLY
- Solder a jumper between points labeled AA on the the MYW-MD main PC board. (see Illustration) This will provide continuous power to the camera, which may cause the camera to be warm. Note: Continually powered, the overall life of the camera will be reduced and condensation may occur.
PS-18C
+
-
+
-
Solder jumper
wire between two
holes in land
pattern.
AA
Solder side view of PC board.
Page 4
IMPORTANT:
FAX (425) 455-0071
E-mail tech-serv@aiphone.com
1198bkjd
Modulator Deviation Control: Contrast control located underneath the cover in the upper right corner of the unit. This applies only when the MYW-MD is used with a CCTV camera. To adjust the picture for more contrast, turn the variable resistor clockwise with a small screwdriver.
OPERATIONS
MODULATOR:
Using the MODULATOR to Integrate a CCTV camera with an Aiphone 2-wire video system:
1. The view from the CCTV camera can be seen on the Aiphone MY monitor by pressing the MONITOR button. With multi-camera systems (MY-2CD, MYW-P3CB & MYW-P3L), the cameras will come up sequentially. (e.g. One press of MONITOR button brings up camera 1, second press brings up camera 2.) After the last camera in the system is activated, the next press of the MONITOR button will turn off the monitor. If the monitor is left on, it will automatically time out after 2-½ minutes.
2. When using a CCTV camera with the LEF/MY system, an audio sub station can be installed near the camera to provide both audio and video monitoring. The station is activated simultaneously from the LEF master
station through the proper connection of the "K#" terminal of the master to the MYW-P3L adapter.
DEMODULATOR:
Using the Demodulator for VIDEO OUTPUT with the Aiphone 2-wire video systems:
1. When the call button is pressed on the MY door station, the inside monitor station will ring and the picture will
come on. At that time, the video signal out of the MYW-MD adaptor will be present, and the picture can be seen on the remote monitor.
2. When the MONITOR button on the inside Aiphone station is pressed, the picture will come up for approximately
2-½ minutes and video signal sent to the monitor via the MYW-MD.
3. The video signal can be connected to any receiving device that accepts a composite video signal (75 ohm, 1V peak-to-peak). This could be a standard CCTV monitor, a video input on a switcher or a multiplexer
system that modulates the video onto a cable TV channel. To take the video signal directly into a TV, use a spare video input or go through an RF modulator.
Using the Demodulator to integrate the MY video door station with a standard CCTV monitor:
(No audio communication or PanTilt is possible with this application)
1. To view the camera location at any time, the camera must be powered at all times, or a switch must be installed
to turn it on. To do this, the PC board must be modified by adding a jumper wire in the location indicated on the wiring diagram on page 3.
2. There is no PanTilt control of the camera when used in this application. To adjust the angle of the MY-DC at the
time of installation, remove the Lexan® dome and move the camera head to the desired angle. Replace the dome and install the unit. If an MY-CA video door station is used, the camera view will be centered and is not adjustable.
3. If the camera is powered continually, there will always be a video output from the MYW-MD. There is no audio communication possible through the door station. This application will shorten the life of the camera.
SPECIFICATIONS:
Power: 18V DC. Use Aiphone model PS-18C (or PS-18YC/A with MY-1CD) Current consumption: 100mA as Modulator; 500mA as Demodulator Wiring distance: ALL DISTANCES ARE USING 18 AWG WIRE
Modulator: Max. 330' from MYW-MD to MY Monitor/adaptor Demodulator: Max. 30' from MY monitor when used for video output
Max. 330' from MY door station when used with a standard monitor Power supply: Max. 16' to MYW-MD Dimensions: 5-1/2"H x 3"W x 1-1/2"D COAXIAL CABLE: 75 ohm, copper center conductor, copper braid, 95% coverage.
Aiphone Communication Systems 1700 130th Ave. N.E. Bellevue, WA 98005 (425) 455-0510
DC resistance: Max, 15 per 1000 feet.
Toll Free Technical Support:
1-800-692-0200
FAX: 1-800-832-3765
Pg. 4
MYW-MD Instr.
Loading...