Page 1
83814600 0596®
MY Series
PanTilt VIDEO DOOR STATIONS
® AlPHONE
Models:
MY-EA
MY-FA
INSTALLATION & OPERATION MANUAL
SYSTEM OUTLINE & FEATURES---------------------------------
MY-EA & MY-FA are semi-flush mount pan and tilt video door stations, which
can be used with any Aiphone MY video system (MY-1CD, MY-2CD, MY/IE,
MY/TD-H. MY/LEF).
For 1 entry;
MY-1CD MY-CU MYW-P1L
Dl
Connecting
Terminals
FEATURES
• Audio, video, and PanTilt control on 2 wires
• Pan and tilting of door camera
• 100m, 330' from camera to monitor on 1.0mm dia.,
18AWG wire
• Extended distance to 300 m, 980' with MYW-BA adaptor
(using 1.2mm dia., 16AWG PE jacketed wire)
• Can replace an existing doorbell using the same wire
(remove existing transformer)
A1.A2 1A1.1A2 A1.A2 1A1.1A2 1A1.1A2 1A1, 1A2
NAMES AND FUNCTIONS
MY-FA
MY-EA
For 2 or max. 3 entries;
MY-2CD MYW-P3CB MYW-P3L
¡5
-jJ
2A1.2A2 2A1.2A2 2A1.2A2
3A1.3A2 3A1.3A2
The MY-EA/FA, when measured at 50 cm, 20" from the camera,
views an area of 51 cm, 20" vertically by 72 cm. 29" horizontally.
On any and every inside monitor, operate Pan/tilt control pad to
maximize viewing area, and Backlight button to view dimly lit or
strongly backlit areas.
.J
LAYOUT EXAMPLE
Refer to the Installation & Operation manual packed with
main monitor or adaptor.
MY-FA
PACKAGE CONTENTS
' PanTilt video door station
(MY-EA or MY-FA)
’ Tamper-proof screwdriver
• Packet of screws
• Installation & Operation Manual
MY-2CD MYH-2CD MYH-2CD
I
INSTALLATION & WIRING
Wiring
Use 2-conductor (parallel) cable.
Coaxial cable or 2 separate wires
should not be used.
When existing chime wires are used, it is possible that the wires may
contain AC voltage current. Locate and remove the bell transformer
before actually connecting MY-EA/FA.
Extra pair(s) in the installed cable can
affect image quality, and must be
terminated with a 120 ohm resistor at I
each end of wires on both MY-EA/FA '
and inside monitor(s). my;“’
Parallel conductor cable
...................
(Extra wires)
S|A1B-
--- - - - - - ----
III A2[^
YES
ty
—
- - - - - - - - - - ®
-- - - - - - - - -
vtf
Installation
MY-EA/FA employs a CCD
camera, and its performance can
be affected by bright direct light,
such as strong sunlight, gate light
or street or porch light which is
directed into the camera lens. Use
backlight button to compensate
for silhouetted images.
Strong
light
source
Page 2
MOUNTING
Front^anei
Screwdriver fl Tamper-proof
supplied ^ screw
MY-EA/FA
_ Four screws 3-5/16”
Two screws supplied
attached
Mounting 3-gang box
bracket ’’"^9
/" 83.5mm
★ Before wiring on MY-EA/FA, make sure using video monitor is not
powered.
1. Loosen the front bottom screw using supplied screwdriver, and lift off
front panel.
2. Loosen 2 screws on MY-E/VFA to separate mounting bracket.
3. Attach the bracket to 3-gang box ring with 57mm, 2-1/4" depth
secured. Note UP-direction marking.
4. Connect 2 parallel wires on non-polarized At, A2 terminals with
secured insulation.
5. Mount unit on mounting frame and reattach front panel.
★ Do not apply any sealant around MY-E/VFA front panel, as openings
are provided for ventilation.
WIRING
Wiring is non-polarized with 2 parallel wires on At, A2 terminals
of MY-E/VFA.
Wiring distance: MY-EA/FA to Video-monitor MY-1CD ,etc.
Diameter 0.65mm 1.0mm
Distance 50m 100m
MY-1CD or
MYW-P1L (LEF)
MY-EA or MY-FA
AWG
Distance
22AWG
^165'
j (door 1) MYW-P3CB (IE-8MD,
MY-CU,MY-2CD,
I TD-H. etc.)
(door 2) or MYW-P3L(LEF)
18AWG
330'
B
TECHNICAL PRECAUTIONS
MY-EA/FA has a camera angle presetting feature, programmable on inside
video monitor. Refer to each Manual of MY-1 CD, MY-2CD, etc.
•installation location:
The MY-E/VFA is weather resistant, but for best results it should be protected
from direct weather conditions. An eave or overhead cover is recommended to
protect it from direct rainfall.
•Temperature;
The MY-E/VFA is rated to operate at temperatures between -10° and 60°C (14°
I SPECIFICATIONS
Power source
Camera unit
Scanning lines
Image viewing area
Minimum illumination
Dimensions & weight
Camera is powered from monitor unit
CCD camera
525 lines
at 50 cm, 20" from camera
Vertical 90cm, 3'. Horizontal 180cm, 6’
(140cm, 47" in still position) when panned and tilted fully
1 Lux at 50cm, 20" from camera
MY-EA/FA
162mm high x 115mm wide x 12.5mm deep.
Approx. 400g. (0.88 lbs.)
H6-3/8"xW 4-1/2" xD 1/2".
Recessed 43mm, 1-11/16",
---------------------------
--------------
OPERATIONS
The red LED is lit to locate call button, day or night. A single
push of Call button activates inside video monitor, as well as
a 4 or 2-tone chime (or other). When inside station replies,
talk handsfree.
Poor lighting conditions:
The MY-E/VFA’s infrared illumination will light the image of
the caller when positioned within 50cm, 20" in front of the
camera, and will see in near darkness (1 Lux of light).
and 140°F). When the outside temperature lowers rapidly, the camera lens may
fog up slightly, causing a blurry picture at the inside monitor. The ventilation
openings will allow the moisture to evaporate, and the picture will return to
normal.
• Cleaning:
Clean the unit with a soft cloth and neutral household cleanser. Do not use an
abrasive cleaner or cloth.
Pan/till viewing area shown by dotted line
28cm {11")
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. 11 this equipment does cause harmful inteference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or reiocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.
Aiphone warrants its products to be free from defects of material and workmanship under norma! use and service for a period of two years
after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which examination
shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision whether there is a
defect in materials and/or workmanship; and whether or not the product is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of
instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
Aiphone Co., Ltd. Nagoya, Japan
Aiphone Corporation, Bellevue, WA, USA
MY-EA/FA-I (E) 0596B
WARRANTY
COMMUNICATION SYSTEMS
® AIPHONE
— HOME, BUSINESS, INDUSTRY.
Printed in Japan (E)
-I-
•i*
-i*
-i*
-i-
Loading...