83696600 0995®
MY Series
PanTilt DOOR STATION
® AlPHONE
Models:
MY-DC/A
MY-DG/A
INSTALLATION & OPERATION MANUAL
SYSTEM OUTLINE & COMPONENTS
MY-DC/A and MY-DG/A are semi-flush PanTilt doorstations for use with MY Series Video Entry Security
system.
----------------
: PS-18YC/A or PS-18YD/A
I : PS-18C orPS-18D
I : PS-12C or PS-12A
Multiple PanTilt entries
•Audio, video, and PanTilt control on 2 wires
• Pan and tilting of door camera
• 100m, 330' from camera to monitor on 1.0mm dia.,
18AWG wire
■ Extended distance to 300 m, 980' with MYW-BA
adaptor (using 1.2mm dia., 16AWG PE jacketed wire)
•Can replace an existing doorbell using the same wire
(remove existing transformer)
NAMES AND FUNCTIONS
CCD camera
■ PanTilt video door station
(MY-DC/A or MY-DG/A)
' Panel lock remover
' Packet of screws
' Installation & Operation Manual
★ Refer to the Installation & Operation
manual packed with main monitor or
adaptor.
MY-DC/A, MY-DG/A
image viewing area (approximate)
j : when camera is panned and tilted fully
□ : when camera is in stili position.
----------------
180cm(6’)
------------------
H
The MY-DC/A and MY-DG/A, when measured at
50 cm, 20" in front of the camera, views an area
of 49 cm, 19" vertically by 66 cm, 26" horizontally.
On any and every inside monitor, operate Pan/tilt
control pad to maximize viewing area, and
Backlight button to view dimly lit or strongly
backlit areas.
Camera
tilts down.
Camera pans to right.
PRECAUTIONS ON INSTALLATION & WIRING
I Wiring
Use 2-conductor (parallel) cable.
Coaxial cable or 2 separate wires
should not be used.
★ When existing chime wires are used, it is possible that the wires
★ Extra pair(s) in the installed cable can affect image quality, and must
Parallel cable
120£J
irjl'l A1
iJill) A21K“
MY-DC/A,
MY-DG/A
may contain AC voltage current. Locate and remove the bell
transformer before actually connecting MY-DC/A or MY-DG/A.
be terminated with a 120 ohm resistor at each end of wires at both
MY-DC/A or MY-DG/A and inside monitor(s).
Extra wires
\
&
■"41
WIRING--------------------------------
MY-DC/A
MY-1CD
MYW-BA
MY-2CD MYW-P3L
120i2
U
MY-1CD,
etc.
Installation
strong light source
MY-DC/A and MY-DG/A employ a
CCD camera, and its performance can
be affected by bright direct light, such
as strong sunlight, gate light or street
or porch light which is directed into the
camera lens. Use backlight button to
compensate for silhouetted images.
TB-ADM10
MYW-P3CB
MOUNTING
------------------
■ Semi-flush mounting
1. Unlock front cover at bottom, using the tool supplied.
2. Attach the mounting bracket to 3-gang box.
MY-DC/A
Polycarbonate
cover
3-gang box
1A1
1A2
3. Mount MY-DC/A or MY-DG/A unit on the bracket,
fastening 2 screws.
4. Replace front cover and click the tip to lock.
1A1
1A2
2A1
2A2
3A1
3A2
1st MY
video door
2nd
3rd
1A1 4A1
1A2 4A2
2A1
10A1
2A2
10A2
3A1
3A2
MY-DG/A
Aluminium
cover
1 Surface-mounting (MY-DC/A only)
1. Mount the MYW-R box on wall or single-gang box.
2. Attach MY-DC/A with 2 mounted screws. Mounting
bracket is not used.
MYW-R; 188 Hx118 WX36 D (mm).
Weight lOOg (0.22 lbs.) approx.
7-3/8”H X 4-5/8”W X 1 -3/8"D.
MYW-R
-3-
OPERATIONS
The red LED is lit to locate call button, day or night. A single push of Call button activates inside video monitor, as well as a 4 or
2-tone chime (or other). When inside station replies, talk handsfree.
Poor lighting conditions:
The MY-DC/A and MY-DG/A's infrared illuminafion will light the image of the caller when positioned within 50cm, 20" in front of
the camera, and will see in near darkness (1 Lux of light).
TECHNICAL PRECAUTIONS
MY-DC/A and MY-DG/A do not have a camera angle
presetting feature.
■ installation location:
The MY-DC/A and MY-DG/A are weather resistant, but for
best results it should be protected from direct weather
conditions. An eave or overhead cover is recommended to
protect it from direct rainfall.
Temperature:
The MY-DC/A or MY-DG/A is rated to operate at
temperatures between -10° and 60°C (14° and 140°F).
When the outside temperature lowers rapidly, the camera
lens may fog up slightly, causing a blurry picture at the inside
monitor. The ventilation openings will allow the moisture to
evaporate, and the picture will return to normal.
Cleaning:
Clean the unit with a soft cloth and neutral household
cleanser. Do not use an abrasive cleaner or cloth.
a SPECIFICATIONS
Power source
Camera unit
Scanning iines
image viewing area
Minimum iliumination
Dimensions & weight
H W D
MY-DC/A
MY-DG/A
*Both 33mm,
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur In a particular installation. If this equipment does cause harmful inteference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of two
•Í*
years after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which
examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision
•Í-
whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of
instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
190 120 36 (mm) 500g
7-1/2' A-m" 1-1/2"
200 120 37 (mm) 560g
8"
1-1/4'recessed
Camera is powered from monitor unit
CCD camera
525 lines
at 50 cm, 20" in front of camera
Vertical 90cm, 3'. Horizontal 180cm, £
when panned and tilted fully
1 Lux at 50cm, 20" from camera
Weight approx.
130cm
{4’3”)
Camera
center
Pan/tilt viewing area shown by dotted iine
29cm (11”)
-200cm (67")
-171cm (5^8”)
90cm (3')
-122cm (4)
-110cm (3’81
12cm (5”)
,57cm (22”)i 66cm (26”) i57cm (22”)
^
---------------
1.10 lbs.
4-3/4"
1-1/2“ 1.23 lbs.
♦ ■*: ♦ ^
0cm 50cm (20”)
WARRANTY
♦
MY-DC/A,
MY-DG/A
122°
^180cm (6’) ^
: Viewing area of camera in still position.
All figures are approximate.
-------------
0cm
50cm
(20”)
•i-
-Í*
Aiphone Co., Ltd., Nagoya, Japan
Aiphone Corporation, Bellevue, WA, USA
W1Y-DC/A-I(E) 0995D
-4-
COMMUNICATION SYSTEMS
©
AIPHONE
HOME, BUSINESS, INDUSTRY.
Printed in Japan (E)
Loading...