83169700 07951
DOOR SENTRY
VIDEO ENTRY SECURITY INTERCOM
® AlPHONE
Models;
MJ-1AD
MJS-1AD/A
(Video Monitor)
(Set)
INSTALLATION & OPERATION MANUAL
CONTENTS
1. SYSTEM OUTLINE & COMPONENTS..................................................................................................................1
2. NAMES & FEATURES............................................................................................................................................2
3. PRECAUTIONS ON INSTALLATION & WIRING...................................................................................................2
4. WIRING................................................................................................................................................................3~4
5. MOUNTING.............................................................................................................................................................4
6. OPERATIONS ON MJ-1AD.....................................................................................................................................5
7. TECHNICAL PRECAUTIONS............................................................................................................................... 6
8. SPECIFICATIONS...................................................................................................................................................6
SYSTEM OUTLINE & COMPONENTS
■ System outline
MJ-1 AD is a video monitor intercom for use with MJ-DS, wide-angle door station.
One or two MJ-1 AD monitor(s) can be installed in system.
------------------------------------
MJ-1 AD
Components available
MJ-DS
Set box is available:
MJS-1AD/A. C, containing MJ-1 AD, MJ-DS & PS-18YC/A
MJS-1AD/A. D, containing MJ-1 AD, MJ-DS & PS-18YD/A
Package contents
Video monitor (MJ-1 AD)
Packet of screws
Installation & Operation Manual
MJ-1 AD PS-18YD/A, 220/240V AC
PS-18YC/A, 120V AC
-1 -
#1
C NAMES & FEATURES
Features
* MJ-DS employs CCD camera, 250,000 pixels
* Infrared LEDs for viewing in near darkness (1 Lux)
* Wide angle viewing of 70cm vert, x 100cm horiz. (2’3” V x 3’3” H)
* Automatic backlight control
* Distance of 150m, 500’to MJ-DS
* Camera angle can be adjusted upwardly by 14°
* Audio and visual monitoring
* Optional second MJ-1 AD monitor
i3l PRECAUTIONS ON INSTALLATION & WIRING
/K Caution
Do not connect any terminal on any unit to AC power lines. It can cause unit damage.
Do not attempt to install or connect wires on MJ-1 AD equipment while power supply is plugged in.
MJ-1 AD monitor unit is designed for indoor use only. Do not install outdoors. MJ-DS
door station is weather resistant.
For system’s installation, there is no need to disassemble any equipment. Wiring
connections are on the back of the units. Do not take unit apart unless properly
qualified.
Any other manufacturer’s products installed with this system (power supply, etc.) are not
covered under Aiphone’s warranty.
Do not mount MJ-1 AD equipment in the following places, as it may cause the system’s
malfunction:
• High or extreme cold temperatrue areas: under direct sunlight, near equipment that
varies in temperature, in front of air conditioner, inside a refrigerated area, etc.
• Places subject to moisture or humidity extremes.
• Places subject to environmental conditions, such as dust, oil, chemicals, etc.
MJ-1 AD is an electrical device, which must not be subjected to water, or any other liquid.
Before actually installing the MJS-1AD/A, the contents of this manual must be thoroughly read and understood. - 2 -
WIRING
Cable requirements
Use a parallel conductor cable. Coaxial cable should
not be used.
When existing chime wires are used, it is possible that the
wires may contain high voltage current. Locate and remove
the bell transformer before actually connecting
MJ-DS.
Extra pair(s) in the installed cable can affect image quality,
and must be terminated with a 120 ohm resistor at each
end on both MJ-DS and MJ-1AD.
Installation location
MJ-DS
MJ-DS employs CCD
camera and the
performance can be
affected by bright
direct light, such as
strong sunlight, gate
light, or street or porch
light which comes
directly into the
camera lens.
Parallel cable Coaxial cable
YES
120 ohm 120 ohm
MJ-1AD
Mount the video-monitor so
that the center of monitor
screen comes to the eye
level of the user.
NO
120 ohm
MJ-1AD
When camera height is too low
MJ-DS is equipped with a camera-angle
adjuster on back of the unit. Pull down this
lever to adjust the camera angle up by 14°.
Lever
Pull down to
turn up the
MJ-DS
camera.
When installing a second MJ-1 AD
Extend 2 wires (and 2 for door strike) from
MJ-1 AD to 2nd monitor, which install within
150m, 500’ max. allowed from MJ-DS.
YES NO
P
Ü
150 m
500’
Wiring diagram
• MJS-1AD/A system
★ Strictly observe polarity.
MOUNTING
MJ-DS
The cover at the bottom conceals the mounting screw.
1. Loosen a screw at bottom of front panel. Lift it off
from back case to separate.
2. Mount back case to single-gang box at two points.
3. Connect 2 parallel wires on non-polar A1, A2.
4. Remount MJ-DS aligning on top, and fasten
bottom screw. Reattach the cover.
★ Do not apply any sealant around MJ-DS back
case, as openings are provided for evaporation.
2 MJ-1AD monitor system
Single-gang
MJ-1AD
Mounting bracket is attached on back of MJ-1 AD.
1. Attach the bracket to wall or single-gang box at two
points.
2. Connect 2 wires from MJ-DS on non-polar A1, A2.
3. Connect 2 wires from PS-18YC(D)/A to 18V DC
terminals. (Red: +, Black: -)
4. Mount MJ-1 AD onto the prongs of bracket, aligning
at marks. Pull it downward until it locks.
5. Plug in PS-18YC(D)/A power supply.
PS-18YC/A( 120V AC), PS-18YD/A (220/240V
AC)
PS-18YC/A
Install the power supply within
1.9m, 6’3” of the monitor.
Bracket
Do not attempt to extend the Screw (2)
DC side of the power supply.
If necessary, extend the AC
side with an extension cord.
(^0
Wood
screw (2)
MJ-1 AD
PS-18YD/A
Screw (2)
(Supplied)
Bracket i
- Do not remove these
two screws
. \
'I#
OPERATIONS on MJ-1 AD
Wide-angle viewing
MJ-DS wide-angle lens sees image of entry 70cm H x 100cm W (2’3” H x 3’3” W)
at 50cm, 20” from camera. The camera has automatic backlight compensation.
Receiving a call from MJ-DS
1 .. . 2
►
Press CALL button momentarily on MJ-DS.
A 4-tone chime is heard and the monitor turns on (it will turn off in approx.
45 seconds if not answered).
Pick up MJ-1 AD handset and communicate.
Replace handset on cradle.
Calling MJ-DS
1. Pick up MJ-1 AD handset.
2. Monitor will turn on.
Two-way communication is established.
Visual monitoring
1. Press MONITOR button on MJ-1 AD.
2. Both monitor and receive audio are turned on.
3. Press MONITOR button to turn off.
Otherwise it will time out in approx. 2-1/2 minutes.
Monitor timer
1. When called, an image is held for 45 seconds. The image is kept on
for 2-1/2 minutes after picking up.
2. Also, monitor is turned on or off with each pressing of the MONITOR button.
Key-marked button
1. Key-marked button provides dry closure contact for door strike.
2. Depress and hold down to activate EL-9S door strike.
Receiving a call at 2nd MJ-1 AD
1. Call-in from MJ-DS rings MJ-1 AD #2 with 4-tone chime and an image.
2. Pick up on MJ-1 AD #2, which shuts off image on MJ-1 AD #1.
No room calling feature
1. MJ-1 AD #1 and #2 cannot call each other.
2. While one MJ-1 AD is picking up, the other
MJ-1 AD cannot join.
Adjustments
TONE, 3-level for controlling chime call tone
and receiver volume in handsfree monitoring.
BRIGHT, 3-level for controlling screen
brightness (and contrast).
TECHNICAL PRECAUTIONS
------------
Installation location:
The MJ-DS is weather resistant, but for best results
it should be protected from direct weather
conditions. An eave or overhead cover is
recommended to protect it from direct rainfall.
Temperature:
The MJ-DS is rated to operate at temperatures
between -10° and 60°C (14° and 140°F). When the
outside temperature lowers rapidly, the camera lens
may fog up slightly, causing a blurry picture at the
inside monitor. The ventilation openings will allow
SPECIFICATIONS
Power source:
Current consumption:
Calling:
Call-in timer:
Monitor timer:
Wiring:
Wiring distance:
Diameter 0.65mm
Distance
• MJ-1AD
Video-monitor:
Scanning line:
Dimensions (H x W x D):
Weight:
75m 150m
DC 18V. Use PS-18YC/A (AC 120V) or PS-18YD/A (AC220/240 V)
Max. 0.8A. 0.05A (standby)
4-tone electronic chime (with 3-level volume control)
45 seconds approx.
2-1/2 minutes approx.
2 parallel conductors (non-polarized)
1.0mm
4" direct view flat CRT
525 lines
210 X 186x61 (mm).
8-1/4" X 7-5/16" X 2-3/8"
Approx. 1,060g (2.34 lbs.)
AWG 22AWG 18AWG
Distance 250’
the moisture to evaporate, and the picture will return
to normal.
Poor lighting conditions:
The MJ-DS’s infrared illumination will light the image
of the caller when positioned within 50cm, 20” in
front of the camera, and will see in near darkness (1
Lux of light).
Cleaning:
Clean the unit with a soft cloth and neutral
household cleanser. Do not use an abrasive cleaner
or cloth.
When camera faces straight forward;
500’
• MJ-DS
Camera unit:
Image viewing area:
Minimum illumination:
Dimensions (H x W x D):
Weight:
This equipment has been tested and found to comply with the limits for a Class В digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular Installation. If this equipment does cause harmful inteference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of two
years after delivery to the ultimate user and will repair free of charge or replace at no charge, should it become defective upon which
examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make the final decision
Ч-
whether there is a defect in materials and/or workmanship; and whether or not the product is within the warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation of
instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does not cover
batteries or damage caused by batteries used in connection with the product.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
•i-
. Ф^ Ф^Ф Ф^ Ф^ Ф*Ф ф|ф Ф^ Ф^Ф
Aiphone Со., Ltd., Nagoya, Japan
Aiphone Corporation, Bellevue, WA, USA
MJ-1AD-I(E) 0795C
CCD camera, 250,000 pixels
70 cm (2’ 3”) vertically, 100 cm
(3’ 3”) horizontally at a distance of
50 cm (20”)
1 Lux at 50cm, 20” from camera
130 X 98 X 37,5(mm).
5-1/8”x 3-7/8” X 1-1/2”
Approx. 230g (0.51 lbs.)
WARRANTY
-6
(All the figures are approximate)
Ф-
Ф.*Ф Ф^ Ф^Ф Ф^ Ф^ Ф^ Ф^Ф ф|ф Ф^ ф|ф Ф^ Ф
0 cm 50 cm (20”)
Ф Ф^ Ф^Ф Ф^ Ф^ ф|ф Ф^ Ф^Ф ф|ф ф|ф Ф^Ф Ф
COMMUNICATION SYSTEMS
® AIPHONE
иГ1ЛЛС nilClMCCC 1МП1 ICTDV
HOME, BUSINESS, INDUSTRY
Printed in Japan (E)
Ф*{Ф
фф{ф
-ь
-ь
•Ì*
ч*
Loading...