Aiphone IC-1AD, IC-1ADU User Manual

0 AlPHONE

830515 0787 E CHIME 1-l/AC-DC

CHIME TONE INTERCOM

TYPE: 1 DOOR - 1 ROOM

MODEL: IC-1AD(U) (AC12A6V, 50/60HZ, or DC12-24V)

- INSTRUCTIONS -

DIMENSIONS UNIT: mm

Handset

-----80--------

FEATURES

^^58

Simultaneous communication system for 1 each door station, room station and door release. Can be powered by a single bell transformer for both communication and door release. May be combined with MC-D/MC-U Video Intercom System (hanging up handset shuts off video monitor). Melodic 4-stroke chime with volume control. Call extension device to announce a chime call from any door in a place remote from room station. Select a most suitable door station from IC-series door stations.

SPECIFICATIONS

* Power source: IC-IAD(U); May be powered by a bell transformer AC 12-16V, 135 mA or more OR a power

supply DC12-24V, 150 mA or more. * Current consumption: 135 mA maximum (AC12-16V). 150 mA maximum (DC12-24V). * Wiring and communication distance: Single pair of wires.

Select the proper wire gauge to meet your requirements from the chart below:

Diameter of wires 0.5 mm 0.65 mm 0.8 mm Distance 90 m 150 m 230 m

Door release:

Use a door release EL-9S (AC 12V, 250 mA) or of other manufacture, which does not exceed AC 12-16V,

1.0 mm 360 m

AWG

24 AWG

Distance 300'

22 AWG 20 AWG 18 AWG

500' 750'

500 mA when powered by a system’s bell transformer. Bell transformer for both communication and door release: AC12-16V, 450 mA or more (for EL-9S). AC12-16V, 700 mA or more (for other manufacture’s).

(inch)

1,180'

BEFORE YOU INSTALL AND OPERATE THE EQUIPMENT - Prohibitions and precautions -

* Operation;

1. DO NOT HOLD HOOK SWITCH DOWN WHILE PICKING UP HANDSET. THE CHIME TONE SOUNDS THRU THE HANDSET RECEIVER ELEMENT AND COULD CAUSE HEARING DAMAGE.

NEVER

* Installation;

1. DO NOT CONNECT ANY TERMINAL ON ANY UNIT TO AC POWER LINES.

When you mount IC-1 AD(U) in place of existing bell or chime, be sure to disconnect wires from the present transformer.

2. Be sure to disconnect wires from bell transformer (or power supply) before you open the IC-IAD(U) unit or make wiring connections.

3. Avoid running the connecting wires thru doors, windows or between furniture, which may pinch and disconnect the wires.

NEVER

4. IC-IAD(U) equipment must be installed in as dry and dust-free environment as possible.

Maintenance;

1. Clean your IC-IAD(U) equipment with a soft cloth dampened with neutral household cleanser. Never use thinner nor benzine, etc.

2. Do not splash water on the door station by hose, etc.

- 1 -

SYSTEM LAYOUT

COMPONENTS AVAILABLE

* Door stations: Select either type from the 1C series door stations;

Door station

IC-DC: w/plastic cover.

Surface-mount.

IC-NA: w/plastic cover.

Semi-flush mount.

IC-RA: w/brown metal cover.

Semi-flush mount.

IC-DA-R; w/plastic cover.

IC-KA; w/brown metal cover.

Semi-flush mount.

Room station

IC-JA: w/stainless steel cover.

Flush-mount.

IC-FY: w/aluminum cover.

Flush-mount.

Surface-mount.

Call extension

IC-D1,IC-DL1; 1-call. IC-D2, IC-DL2: 2-call. IC-D3,IC-DL3; 3-call.

IC-D2, -DL2

w/anodized aluminum cover. Surface-mount. (IC-DL type: with illumina-

IC-D3, -DL3 tion lamp)

Options;

EL-9S: Electric door release.

AC 12 V, 250mA. May be powered by a system’s bell transformer (one per system).

■

ICR-1: Call extension.

Announces a call from door by chime in a place remote from IC-IAD(U) (one per system).

NOTES:

Your lC-1 AD(U) unit can also work with the existing models; IB-DA, IB-NA, IB-RA, IB-RAG, IB-JA, IB-FY and IBR-l/A.

ACTUAL TERMINAL LOCATION

IC-1AD(U)BACK VIEW

For power supply.

Connect to QH , [2] terminals on door station (non-polarized)

Connect to electric door release (non-polarized)

For call extension

(non-polarized)

CASE & CHASSIS

INSIDE VIEW

PC BOARD

(1) Remove 2 screws on back of the chassis and separate front case and chassis. (2) As shown, take out two WHITE wires thru a hole on the chassis. (3) Connect 2 wires to the wires from the ICR-1 (non-polarized).

+ 2 hidden pages