Aiphone AXW-AZ Instruction Manual

AX Series Video Adaptor for CCTV Camera and Audio Door Station

- INSTRUCTIONS -

The AXW-AZ converts a standard CCTV camera's signal to a CAT-5e connection, providing a
signal compatible with the AX Integrated Security and Communication system. This allows the
utilization of a color CCTV camera and a separate audio door station (AX-DM or IE/IF-Series) to be
used in place of an AX video door station. A motion detector or other activation device can be
connected to the Sensor input to trigger camera activation. Video output is provided for continual
viewing and/or recording via composite pass-through. The unit is equipped with a relay output to
trigger an external device, such as a DVR or video switcher whenever the audio and/or video to the
AX system is active.

OUT IN

SENSOR RELAY LINE

NC NC NO NO D1 E1

CEU

75 OHM

VIDEO

TERMINAL DEFINITIONS:

CEU (RJ-45): Output from AXW-AZ to AX CEU Door Station input
LINE D1, E1: AX-DM or IE/IF-Series Audio Door Station input
RELAY NO, NO: Normally Open relay contact, activated when AX video is on.
SENSOR NC, NC: Normally Closed contact, activates call-in function and video at AX master

when tripped by motion detector or other device with N/C contacts.
VIDEO IN: Composite input signal from CCTV camera
VIDEO OUT: Composite output to external CCTV monitor, switcher, DVR, or video input on

another device
75 OHM SWITCH: Termination Switch. Set to OFF position when VIDEO OUT is connected to

CCTV system. Set to ON position when video output is not used.

OFF ON

AIPHONE

COMPATIBLE AUDIO DOOR STATIONS:

AX-DM Mullion mount, black plastic
IF-DA Surface mount, brown plastic
IE-DC Surface mount, brown plastic w/aluminum
IE-JA Flush mount, 2 gang, stainless steel faceplate
IE-SS Flush mount, 2-gang, stainless steel vandal resistant
IE-SSR Flush mount, 2-gang, stainless steel vandal resistant w/red mushroom call button

Pg. 1

WIRING DIAGRAM:

AXW-AZ with Standard CCTV Camera and Audio-only Door Station

AX-DM or IE/IF-Series

Audio Door Station*

IE-JA

1
2

CCTV Camera

75 Ohm, 1V Peak-to-peak
(Independently powered)

Normally Closed input for remote

activation (i.e. motion sensor,

loop detector, etc.)

Normally Open contact for
remote device activation
(i.e. video switcher, DVR, etc.)

VIDEO OUT

CAT-5e to CEU

AXW-AZ

CEU

LINE

D1
E1

VIDEO IN

SENSOR

NC
NC

RELAY

NO
NO

Notes:

1. AX-DM or any IE/IF-Series audio door
station may be used with AXW-AZ.

2. Video Output is optional. If not in use,
set 75 ohm switch to “ON.”

3. When the SENSOR input is used, the
camera will be turned on when the
sensor device is activated (Normally
Closed contact from 3rdparty supplied
device).

When VIDEO OUT is connected,

set 75 ohm switch to OFF position.

Constant video output for
CCTV monitor, DVR, etc.

AX-DM or IE/IF-Series

Door Station Connections*

AX-DM: Red to D1, Brown to E1
IF-DA: 1 to D1, 2 to E1
IE-JA: 1 to D1, 2 to E1

IE-SS: Red to D1, Black to E1

Door station inputs (RJ-45 jacks)

D1 ~ D8 inputs on AX-084C; D1 ~ D24 inputs on AX-248C M1 ~ M4 (M8) inputs on AX CEU

AX-248C

Master station inputs (RJ-45 jacks)

Note:

Only information pertaining to the connection and
operation of the AXW-AZ and devices interfacing
with it are included here. For complete AX system
installation, wiring, and programming information,
please consult the AX Installation Manual
(included on CD with AX Central Exchange Unit).

AX-8MV

Pg. 2